Question: A centrifugal pump shown in Figure 3.1 below has a 100 mm diameter suction pipe and a 75 mm diameter delivery pipe. When discharging

A centrifugal pump shown in Figure 3.1 below has a 100 mm diameter suction pipe and a 75 mm diameter delivery pipe. When discharging 15 L/s of water, the inlet-mercury manometer with one limb exposed to the atmosphere recorded a vacuum deflection of 198 mm; the mercury level on the suction side was 100 mm below the pipe centre line. The delivery pressure guage, 200 mm above the pump inlet, recorded a pressure of 0.95 bar. The measured input power was 3.2 kW. Calculate the pump efficiency. Suction pipe P Delivery pipe 198 mm Mercury manometer 200 mm

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Millhouse graduated 5 years ago with a degree in business administration and is currently employed as a middle level manager for the same firecracker company his dad already worked for. His current...

Financial analysts have estimated the returns on shares of the Woods Corporation and the overall market portfolio under two economic states nature as follows. For Woods the state dependent returns...

Problem 5-23 Payback and NPV An investment under consideration has a payback of six years and a cost of $573,000. Assume the cash flows are conventional. If the required return is 11 percent, what is...

The centrifugal pump shown in Figure E19.20 is used to supply water to a storage tank. The pump inlet is at atmospheric pressure, and water is pumped up to the storage tank, which is open to...

University of Hartford Department of Civil, Environmental and Biomedical Engineering CE 320 Water Resources Engineering Spring Semester 2017 Lab #5 - Pump Performance Characteristics Report Outline...

just need the answers of 4.4, 4.9, 4.11, 4.12 and 4.14 Problems 107 P. 51 5 4.3 A centrifugal pump is required to develop a pressure rise of 30 psi when delivering 1000 gpm. If three motors with...

Water is to be pumped from lake to a second large, close tank with inside pressure of 0.9 bar as shown in figure 1 below. The pipe diameter throughout is 5 cm. and the total length of the pipe...

c ) A liquid fuel with a density of 8 6 3 kg m - 3 and a flow rate of 0 . 7 m 3 s - 1 is to be delivered by the operating pipeline of 1 0 , 8 8 2 m long. The annual charges ( interest on capital,...

Weekly sales with the El Barato Supermarket Family Card are on average $2,570 in its Mayagez store with a standard deviation of $680. Determine what is the probability that in a sample of 81 weeks a)...

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

QUESTION 2 (20 marks) A pump transports a chemical solution at a flowrate of 250 L/s from an underground tank at 20 kPa to a reactor at 40 kPa as shown in Figure 2. The specific gravity and dynamic...

A circular vertical shaft is planned to have a finished, inside diameter of 8 m in an underground hard rock mine. Rock properties are: C o = 189.0 MPa, T o = 12.69 MPa, E = 42.69GPa, = 0.22, =...

Calculate the sample densities Data Table 1. Mass of Pipetted Samples of Water (The first one is done for you. Sample Density (g/mL) mL Sample Mass (g) 1.00 0.99 g D = mass/volume = 0.99 g/1.00 mL =...

Select the best answer. A taxpayer's GILTI inclusion for a tax year is the amount by which its ( computed as an aggregate amount with respect to all CFC ' s with respect to which that taxpayer is a U...

13.44 A small block slides at a speed v on a horizontal surface. Knowing that h 0.9 m, determine the required speed of the block if it is to leave the cylindrical surface BCD when 0 = 30. B DE

Happy Meal Limited a food manufacturer is considering purchasing a new machine for 320,000. The company is expecting an annual cash inflow of 105,000 from the sale of products and an annual cash...

1. What is the merchanism of synthesis of salicylamide? 2. Does the boiling temperature too high affect the performance synthesis of salicylamide? 3. Comparison of likelihood of an amide reaction...

The liquid level in a tank is controlled using a Pneumatic proportional controller as shown the figure below. The level sensor is able to measure over the range 1.85 to 2.25 m. it is found that,...

6 Theory of Machines 5. A shaft carries five masses A, B, C, D and E which revolve at the same radius in planes which are equidistant from one another. The magnitude of the masses in planes A, C and...

Consider a simple liquid phase reaction in which reactant A is converted to product B. The reaction is second order in A and the kinetics are given by the equation A stream of material A of...

Consider the compression of feed air into a process that produces maleic anhydride, shown in Figure P14.6. The air enters the process at a rate of 10 kg/s at atmospheric pressure and 25C. It is...

Acrylic acid at 89C and 0.16 kPa ( = 970 kg/m 3 , = 0.46 cP) leaves the bottom of a distillation column at a rate of 1.5 L/s. The bottom of a distillation column may be assumed to behave like a tank...

Relative Frequency Histogram I Construct a relative frequency histogram for these 50 measurements using classes starting at 1.6 with a class width of .5. 16. What fraction of the measurements are...

18. What proportion of the measurements are less than 2? Construct a relative frequency histogram for these 20 measurements on a discrete variable that can take only the values 0, 1, and 2. 2007 100...

17. What proportion of the measurements are greater than 1? Construct a relative frequency histogram for these 20 measurements on a discrete variable that can take only the values 0, 1, and 2. 2007...