Question: A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and

A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A 250-mm-wide strip with a thickness of 20 mm is fed through a rolling mill with two powered rolls, each of radius = 200 mm. The work thickness is to be reduced to 17 mm in one pass at a roll speed...

Q1) Determine the cutting force and feed (thrust) force for a turning operation using the following parameters: Material tensile strength 250MPa, Shear strength 120 MPa, chip thickness ratio r =...

The wide-flange shape has dimensions of bf = 7.30 in., tf = 0.9 in., d = 18.5 in., and tw = 0.8 in. A vertical shear force of V = 49000 lb acts on the cross section. Determine the shear flow...

. 54. ABC, a domestic corporation, 60% Filipino owned, had the following gross receipts from world championship events it conducted in the Philippines: Billiards (between Bata Reyes & Don Ming S...

Choose the correct answer only, no explanation is needed. Abdul Company is engaged in a variety of businesses around south. The CEO thought of expanding and the way to do that is to buy a portion or...

Problem 4 ( 2 0 points ) A drilling operation is performed to create a through hole on a steel plate that is 2 0 mm thick. Cutting speed is 0 . 5 m s , and feed is 0 . 2 2 m m r e v . The 1 9 - m m -...

Tim O d. Gibreth A through hole of diameter 20.0 mm is to be drilled through a steel plate that is 50 mm thick Cutting conditions are: cutting speed - 25 m/min, feed- 0.08 mm/rev, and the point angle...

So far, we have discussed identifying and recording/analyzing transactions. From there, we would post journal entries to the general ledger and made an unadjusted trial balance. From there, we would...

A numerical control drill press drills four 10.0 mm diameter holes at four locations on a flat aluminum plate in a production work cycle. Although the plate is only 12 mm thick, the drill must travel...

Using lathe & drilling machines, for 8 hr/day, an operator is cutting down a part to a specific size (see Figure in next Worksheet). Three main elements are needed: (A) Set part into Vice, (B)...

Ben knocked on the door of Nancy Kerr, his supervising director. Come in, Nancy said, and Ben entered. He was frustrated, and his demeanor reflected it. I need to talk to you about Stacey Burton, who...

1. Because of rising costs, Frito-Lays contribution margin has decreased to 30 percent. Refer to Appendix 2, Marketing by the Numbers, and calculate the contribution per ounce Frito-Lay realizes if...

At which points is the function continuous? y = 2 x - 1 4 The function is continuous on 1 2 , ( Smplify your answer. Type your answer in interval notation Use intepers or fractors for any numbers in...

A substantial portion of inventory owned by Prentiss Sporting Goods was recently destroyed when the roof collapsed during a rainstorm. Prentiss also lost some of its accounting records. Prentiss must...

The following selected data were taken from the financial statements of Robinson Inc. for December 31, 2014, 2013 and 2012: The 2014 net income was $372,000, and the 2013 net income was $492,000. No...

Journalize the following transactions that occurred in September 2018 for Aquamarines. No explanations are needed. Identify each accounts payable and accounts receivable with the vendor or customer...

At the end of the year, Randys Parts Co. had the following items in inventory: Required a. Determine the amount of ending inventory using the lower-of-cost-or-market rule applied to each individual...

Prepare Quality Office's multi-step income statement for the year ended March 31, 2018. The adjusted trial balance of Quality Office Systems at March 31, 2018, follows: QUALITY OFFICE SYSTEMS...

12:11PM Tue Jul1 BR cee Fare) |- Student Portal | Mair X | {2 mms.mckesson.com X | @ MGT-655 Calendar X | TOC Financial Measi X | Course Hero x Question3-Topics X + x Cc ezto.mheducation.com ef -...

(b) Lower and upper control limits for the R chart.

What are the five categories of material transport equipment commonly used to move parts and materials inside a facility?

Two stepping motors are used in an open loop system to drive the lead screws for xy positioning. The range of each axis is 250 mm. The shafts of the motors are connected directly to the lead screws....

=+Obs Dep Var Value Residual 1 0.6100 0.3548 0.2552 2 0.8400 0.7939 0.0461 3 1.5120 1.3209 0.1911 4 1.7920 1.9357 -0.1437 5 2.9520 2.6383 0.3137 6 2.8800 3.4287 -0.5487 7 4.4000 4.3069 0.0931 8...

=+a. Does a scatterplot of the data suggest an appropriate linear relationship between x and y?

=+by the authors, compares y 5 reduction rate of transmittance (%) and x 5 sandblast momentum (g .m/s) for 14 PMMA and 8 glass substrate samples: