Question: A falling head hydraulic conductivity test was a silty clay soil sample ) = ( 2 . 7 0 . The sample was 1 2

A falling head hydraulic conductivity test was a silty clay soil sample )=(2.70. The sample was 127mm long with a diameter of 100mm. The diameter of the standpipe was 7mm. The temperature of the water used to conduct the test was 22C. After 1081 seconds, the water level in the standpipe dropped from 560mm to 465mm. Calculate:
a. temperature-corrected hydraulic conductivity in cmsec.
b. the time required for a similar head and drop if a standpipe 4mm in diameter was used instead.
A falling head hydraulic conductivity test was a

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Q 3 ( 3 0 p . ) A falling head hydraulic conductivity test has been conducted on a clay sample. The soil sample was 5 5 m m in diameter and 1 2 0 m m tall. The standpipe had an inside diameter of 6 m...

Q:

A constant head constant head hydraulic conductivity test was run on a layered soil shown in figure. The area of the soil sample in the test is 0 . 1 m 2 , flow rate through the system is 1 6 0 c m 3...

Q:

A constant head hydraulic conductivity test is conducted on a sample of soil proposed as a drainage layer in a landfill cover system. The sample has a length of 8 inches and a diameter of 4 inches....

Q:

Question 2 [ 8 ] A layer of clay 4 m thick lies between two layers of sand each 4 m thick. The water table is 2 m below ground level. The lower layer of sand ( the one below the clay ) is under...

Q:

[ 2 0 Points ] A falling - head permeability test was performed on a soil sample 9 7 - m m in diameter and 2 0 - m m long. The standpipe had an inside diameter of 6 . 0 m m . The water level in the...

Q:

acela om Question 2.129 marks) 1. A All material being proposed for use as a subbase for a highway project has passed 64% through No 10 sieve (2.00mm) 33% through No 40 sleve (0.425mm) and 10%...

Q:

In falling head test, the specimen length was 2 0 0 m m , the cross - section area of the specimen was 1 , 0 0 0 m m 2 , the cross - section area of the standpipe was 4 0 m m 2 , the initial head...

Q:

a) A capillary tube can serve as a model for capillary rise in soils. In this model, the capillary fise height, h, above the water table is given as: h=gR2cos where is surface tension, is contact...

Q:

Question 3 [ 1 2 ] A 3 . 8 m deep silty sand layer overlies a 5 . 6 m thick normally consolidated clay layer, the clay is underlain by dense gravel. An oedometer test was conducted on the sample of...

Q:

A falling head permeameter test was conducted using the setup shown in Fig. 1 with the conditions below. mass of the dry soil sample Ms: 1 6 0 0 g mass of the water in the sample M w : 3 8 0 g soil...

Q:

A piece of copper wire has a resistance per unit length of 5.90 103/m. The wire is wound into a thin, flat coil of many turns that has a radius of 0.140 m. The ends of the wire are connected to a...

Q:

Under what conditions would the simple interest rate, or APR (remember rSIMPLE APR), equal the effective annual rate, rEAR?

Q:

In May 2 0 2 4 , Sandra's office was burglarized, and she determined that approximately $ 2 1 , 0 0 0 of equipment was taken. In September 2 0 2 4 , she received a reimbursement check from the...

Q:

Robert Inc. has total monthly maintenance costs that fluctuate with varying direct labour hours as follows: Maintenance Labour Hours Cost January $14,500 3,500 February $13,960 3,600 March $11.500...