Question: A horizontal venturimeter having 3 0 cm inlet diameter and 1 5 cm throat diameter is used to measure the flow of oil of specific

A horizontal venturimeter having 30 cm inlet diameter and 15cm throat diameter is used to measure the flow of oil of specific gravity=0.8. Find the flow rate of oil through venturimeter if the reading of the oil-mercury differential manomter is 2.5 cm. Take Cd=0.98.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Determine the force in members BC, HC, and HG. After the truss is sectioned use a single equation of equilibrium for the calculation of each force. State if these members are in tension or...

Q:

(a) A venturi-meter of 150 mm (inlet diameter), 75 mm (throat diameter) size is used to measure the flow rate of oil having specific gravity of 0.9. The reading shown by the L tube manometer...

Q:

In account Q1: A horizontal venturimeter with inlet diameter 20 cm and throat diameter 10 cm is used to measure the flow of oil of sp. gr. 0.8. The discharge of oil through venturimeter is 60...

Q:

b) A horizontal Venturimeter with inlet diameter 20 cm and throat diameter 10 cm is used to measure the flow of 5 water. The U-tube differential manometer is attached having Hg as a manometric fluid....

Q:

1. A horizontal venturimeter, with inlet and throat diameters 300 mm and 100 mm, respectively is used to measure the flow of oil of specific gravity 0.88. The pressure intensity at inlet is 130kN/m...

Q:

A mixture of natural talc and borax is obtained via surface mining techniques and is delivered in open- top trucks to the plant site. At the plant site it is crushed by large jaw crushers into pieces...

Q:

An ideal Rankine cycle operates with a high - pressure steam at 6 MPa and 5 0 0 C , and it condenses at 0 . 1 MPa. Calculate: a . The thermal efficiency of the cycle. b . The specific work output. c...

Q:

An ideal Rankine cycle operates with a high - pressure steam at 6 MPa and 5 0 0 C , and it condenses at 0 . 1 MPa. Calculate: a . The thermal efficiency of the cycle. b . The specific work output. c...

Q:

An ideal Rankine cycle operates with a high - pressure steam at 6 MPa and 5 0 0 C , and it condenses at 0 . 1 MPa. Calculate: a . The thermal efficiency of the cycle. b . The specific work output. c...

Q:

An ideal Rankine cycle operates with a high - pressure steam at 6 MPa and 5 0 0 C , and it condenses at 0 . 1 MPa. Calculate: a . The thermal efficiency of the cycle. b . The specific work output. c...

Q:

An ideal Rankine cycle operates with a high - pressure steam at 6 MPa and 5 0 0 C , and it condenses at 0 . 1 MPa. Calculate: a . The thermal efficiency of the cycle. b . The specific work output. c...

Q:

Answer true or false to each statement, and explain your answers. a. The graph of a linear equation slopes upward unless the slope is 0. b. The value of the y-intercept has no effect on the direction...

Q:

Explain the difference between a point estimate and an interval estimate.

Q:

12. Fig. 3D.16 shows four different oscilloscope traces of sound waves. (a) Which of the sound waves, A, B, C or D, has the highest pitch? (b) Which of the sound waves, A, B, C or D, has the lowest...

Q:

Ants from urban locations tolerate heat slightly less than ants from rural locations. There was a flaw in the experimental design. There is little to no difference in the heat tolerance of ants from...