Question: A pin in a knuckle joint is subjected to an axial load of 900 kg. The thickness of the eye is to be 1.5

A pin in a knuckle joint is subjected to an axial load

A pin in a knuckle joint is subjected to an axial load of 900 kg. The thickness of the eye is to be 1.5 times the diameter of the pin. The allowable stress of the material in tension and compression due to bending is 65 MPa. The allowable bearing stress may be taken as 30% of the bending stress. Determine the required pin diameter (d) to satisfy bending, shearing and bearing. Yoke Pin Rod A Based on the recommended pin size, design the whole knuckle joint as well as the rod.

Step by Step Solution

★★★★★

3.38 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Answer b Given T For Given 15d F 900kg 900x981 8829N 5 65 mpa 06 03 x 65 19s ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A prismatic bar is subjected to an axial force that produces a tensile stress ÏÎ¸ = 65 MPa and a shear stress ÏÎ¸ = 23 MPa on a certain inclined plane (see figure)....

The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps at the top and bottom distribute the load uniformly throughout the block, determine the average normal...

The polyvinyl chloride bar is subjected to an axial force of 900 lb. If it has the original dimensions shown, determine the change in the angle u after the load is applied. E pvc = 800(10 3 ) psi,...

Audit Implications of the New Revenue Reporting Standard A Panel Discussion By CPAJ Staff Featured, February 2019 Issue | March 2019 Get Copyright Permission About the Panelists The panel featured...

The grains of wood in the board make an angle of 20° with the horizontal as shown. Determine the normal and shear stress that act perpendicular and parallel to the grains if the board is...

A W 12 x 35 steel cantilever beam is subjected to an axial load P = 10 kips and a transverse load V = 15 kips. The beam has length L = 6 ft. (a) Calculate the principal normal stresses and the...

House paint is formulated so that, if applied properly, it will not run down a vertical surface before it dries. It can be modeled as a Bingham fluid. (a) Suppose that a latex paint with a density...

Determine the stress on an aluminum wire, 4 m long and 5 mm in diameter, subjected to an axial load of 450 N

The $\mathrm{W} 10 \times 45$ is made of $\mathrm{A}-36$ steel and is used as a column that has a length of $15 \mathrm{ft}$. If its ends are assumed pin supported, and it is subjected to an...

Need solutions with work for this finance quiz. Consists of 20 questions and is for the class finite analysis. See attached document for full quiz. 1/17/2016 Unit 1 Quiz (2.1, 2.2, 2.3, 2.4)...

Consider a semi-annual coupon bond with 4% coupon rate, $1,000 facevalue and 8 year term. How much is this bond worth if its yield tomaturity is 5%? Round to the nearest dollar. 2 answers

A college basketball coach has 12 players on his team. Eight players are receiving scholarships, and four are not. The coach decides to select a starting lineup by selecting five names out of a bowl....

A. Suppose stock in Watta Corporation has a beta of .80. The market risk premium is 6 percent, and the risk-free rate is 6 percent. Watta's last dividend was $1.20 per share, and the dividend is...

Annie's Bakery sold $5,000 of cookies this month. Annie determined that her fixed costs are $2,000 per month and her net operating income was $1,000. What is Annie's Bakery's contribution margin? a.)...

Five sequential operations have the following hourly production rates. A=150, B=175, C=95, D=88, E=120. What is the hourly throughput rate?

Tata Motors is primarily targeting emerging countries (e.g., Africa, Asia Pacific, Middle Eastern, and Latin America for its future exported growth.) Is this a viable and logical exporting strategy?

A local real estate investor in Orlando is considering three alternative investments: a motel, a restaurant, or a theater. Profits from the motel or restaurant will be affected by the availability of...

The manager of a local convenience store is expanding his line of small toy items. To price these new items, the manager is looking at the prices being charged by competing retailers in his area. For...

The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied torque T, which subjects the material at the tubes outer edge to a shear strain of Î³ max...

The rod has a circular cross section. If it is made of an elastic perfectly plastic material, determine the shape factor for the rod.

Determine the principal stresses, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the element in each case. 20 MPa 80 MPa 30 MPa

In viewing the items above, seeing three columns of Xs on the left versus three rows of Xs on the right can be explained by the Gestalt principle of __________. XX XX XX XXXXXX XX XX XX XXXXXX XX XX...

If Tabitha closes her eyes when she rides in her parents car, she can still tell that the car is moving. This is due to the movement of tiny crystals in the a. otolith organs. b. outer ear. c....

From experience, you know that commercial jets typically fly around 500 miles per hour at a height of 30,000 feet. However, as you watch one fly high overhead, it seems to slowly pass by. What...