Question: A planetary spur gear train as shown in the figure below consists of 34-tooth sun gear in mesh with a planet gear of 22

A planetary spur gear train as shown in the figure below consists of 34-tooth sun gear in mesh with a planet gear of 22 teeth. The sun gear pitch diameter is 136 mm. During power transmission the arm rotates at1200 rpm while the ring is held stationary, 1- Find the diameters of the planet and ring gears (2 pts) 2- The number of teeth of the ring (2) 3- Determine the rotational speeds of the sun gear (4 pts) 4- Find pitch line velocity of the planet gear (2 pts) planet ring gear ring gear sun gear planet arm am sun gear armi input output bearing

Step by Step Solution

★★★★★

3.50 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Accounting Questions!

Carla Armitage owns 100% of the common shares of Extra Ltd., a Canadian-controlled private corporation operating a wholesale business in eastern Canada. Extra's fiscal year end is May 31, 2021. It is...

The device shown in the figure below is used to estimate the thermal conductivity of a new bio material by measuring the steady-state heat-transfer rate and temperature. The bio material is wrapped...

A cast-steel C frame as shown in the figure has a rectangular cross section of 1.25 in by 2 in, with a 0.5-in-radius semicircular notch on both sides that forms midflank fluting as shown. Estimate A,...

A shock mount constructed as shown in the figure is used to support a delicate instrument. The mount consists of an outer steel tube with inside diameter b, a central steel bar of diameter d that...

It is desired to use the finite element method to solve the two plane truss problems shown in the figure below. Assume $A E=10^{6} \mathrm{~N}, L=1 \mathrm{~m}$. Before solving the global equations...

20. Use FEM to solve the two plane truss problems shown in the figure below. Assume AE = 106 N, L = 1 m. Before solving the global equations [K]{Q} = {F}, find the determinant of [K]. Does [K] have...

A stepped diameter shaft is supported by ball bearings as shown in the figure below The bearing has a slight eccentricity that induces a bending moment in the shaft as it rotates Measurements...

Present the loop closure equation that can completely solve the mechanism shown in the figure below, and indicate the known and unknown values for each term in the equation. Find the equation of the...

The section of shaft shown in the figure is to be designed to approximate relative sizes of d = 0.75D and r = D/20 with diameter d conforming to that of standard metric rolling-bearing bore sizes....

In response to a step voltage, the voltage waveform shown in the figure below was observed at the midpoint of a lossless transmission line with Z0 = 50 and up = 2 X 108 m/s....

A cell mono layer used in a tissue engineering scaffold adheres onto the top surface of a silicone rubber (polymer) sheet of 0.10 cm thickness, as shown in the figure below. The rectangular sheet is...

2. The marginal costing operating statement of ABC Limited for the year just ended is as follows: Sales (5,000 units at $4 per unit) 20,000 8,000 Variable costs Contribution 12,000 Fixed cost 7,500...

17. Hand owns 90% of Finger. In 2015 Hand purchases Land from third parties for $500,000. On January 1, 2018 Hand sells Land to Finger for $800,000. Finger holds the Land until December 31, 2020 and...

5 pts Find the derivative of the function. q = 1 4 r - r 7 2 1 4 - 7 r 6 2 1 4 r - r 7 2 - 7 r 6 1 4 r - r 7 2 1 2 1 4 - 7 7 6 2 1 2 1 4 r - r 7 2 Question 1 9

Tuka Pty limited is a company based in Lusaka that was started 20 years ago by two brothers. The company manufactures four similar products produced on the same production machinery. The company has...

The price of carrots per kilogram is given in the table below for several years, as is the corresponding CPI. 2003 2005 2007 2009 2011 2013 Nominal carrot price $ 2.70 3.40 3.00 2.60 2.60 3.40 CPI...

Events A and B are independent. Suppose event A occurs with probability 0.90 and event B occurs with probability 0.58. a. If event A or event B occurs, what is the probability that B occurs? b. If B...

Q2. Lines are drawn parallel to the line 4x 3y + 2 = 0, at a distance 3/5 from the origin. Then which one of the following points lies on any of these lines ? B (,-3) c (; }) D (-,-) 1 A 4 JEE-Main...

Construct: Select the missing element in each drop-down box to construct each term based on the given definition. Inflammation of the appendix: appendic /

An epicyclic gear train consists of sun wheel S, a fixed internal gear E and three identical planet wheels P carried on a star-shaped planet carrier C, as shown in Fig. 15.20. The planets rotate at...

Match List I (Gear Train) with List II (Application) and select the correct answer using the code given below the lists: List I (Gear Train) A. Compound gear train B. Eipcyclic spur gear train with...

Design a compound, spur gear train for a ratio of -70:1 and diametral pitch of 10. Specify pitch diameters and numbers of teeth. Sketch the train to scale. Design a compound, reverted, spur gear...

The standard 2-pass spur gear train with the # of teeth on each gear as shown is driven is driven at 1000 RPM from shaft 2 with a torque of 25 in-lb. All the gears in the set have a diametral pitch...

Problem Statement: A spur gear train consists of three gears connected in series: Gear A , Gear B , and Gear C . The specifications are as follows: Gear A : Driver gear with 2 0 teeth, rotating at 6...

A 16 tooth pinion drives a double reduction spur gear train, as shown. All gears have 25 pressure angles. The pinion rotates counterclockwise at 1,200 rpm and transmits power to the gear train. The...