Question: A shear connection involves a flat bar sandwiched between two connection plates. The plates and the bar are bolted with two 1 4 . 0

A shear connection involves a flat bar sandwiched between two connection plates. The plates and the bar are bolted with two 14.0 mm diameter bolts - meaning that each bolt has two shear planes . The shear strength of the bolts is given as 0.6Fu where the ultimate stress of the bolt material Fu is 830 MPa. Based on the shear strength of the bolts, how much force, T, in kN can the connection carry?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

QUESTION 4 ( 1 3 0 marks ) As indicated in Fig. 4 , two splice plates of Grade 3 0 0 steel with a thickness of 1 2 mm each, are connected together. There are 3 lines and n rows of bolts on the...

Q:

(a) The spliced connection shown in the figure below, is under the effect of an axial tension load (N* = 20 kN) originating from transient wind load actions only and acting along the grains of the...

Q:

Two 8 mm & one 12 mm thick S275 plates, shown in Figure Q2, are connected by two 20 mm diameter Grade 8.8 black bolts. Assuming the bolt is fully threaded and all edges are either rolled or machine...

Q:

Capacity of Connection. The capacity of the connection reflects the beam end-shear equilibrium (CS Fig. 8.2): beam that can be supported. Applying + 1 , = 0: - 0.5V beam + Fm = - 0.5V beam + 37.968...

Q:

A Simply supported beam ( W 6 1 0 x 1 7 4 , ASTM grade 5 0 steel ) of 1 2 meters span is subjected to a total factored uniformly distributed load of 2 2 0 kN / m . The beam is topped by a concrete...

Q:

callculate in SI units A Simply supported beam ( W 6 1 0 x 1 7 4 , ASTM grade 5 0 steel ) of 1 2 meters span is subjected to a total factored uniformly distributed load of 2 2 0 kN / m . The beam is...

Q:

PART A - TESTING OF SHEAR CONNECTIONS SINGLE SHEAR CONNECTIONS a. b. C. Check the diameters of the aluminum (2011-T3) test pins and record in the following table (nominal diameter is 3/16 in = 0.188...

Q:

QUESTION 2 SA A simply supported composho beam forms part of an apartment floor. The composto beam has the following properties and dimensions The effective width of the concrete cover slab is 1800mm...

Q:

1 . Sketch a simple steel beam - to - column shear connection. Indicate where the shear connection is located in the assembly. Label the main components of the shear connection, such as the beam,...

Q:

Qacstion 2 : 1 2 marks ) 2 . ) The beam - to - olumn shear connection below is designed to resist a beam reaction force of P ? iso k N . The connection uses back - to - back angles ( one on each side...

Q:

Many politicians, scientists, economists, and businesspeople have become concerned about the potential implications of global warming. The largest source of the emissions thought to contribute to...

Q:

Bruin Paper Company produces specialty papers. During August, the company produced 50,000 reams of paper. The standard wage rate is $6.50 per hour, and each ream of paper requires 15 minutes of...

Q:

Managerial accounting, as opposed to financial accounting, is primarly concerned with: Mutiple Cholce providing information to ineestors and crednoss. gresem and fiture plowing and control. Nitonka...

Q:

The Town of Quincy's fiscal year ends on June 30. The following data relate to the property tax levy for the fiscal year ended June 30, 2020. a. The balance in Deferred Inflows-Property Taxes was...