A submersible pump is installed 400 ft in a well to supply water to a tank...

Transcribed Image Text:

A submersible pump is installed 400 ft in a well to supply water to a tank T₁ which is 1.5 m x 1.2 m x 1.5 m, and it is 16 m above the ground. The tank T₁ is to supply water to residents In Ekosodin, Professors quarters, BDPA and Faculty of Engineering. A pump P is installed on the line 10 m from the tank and a one-way valve is installed immediately after the pump. A manifold, with 3 shut-off valves is spotted 110 m from the pump. From one end of the manifold, a line is run to a tank T₂ which has a relief valve installed on it. A Tee is placed 10 m from Tank T₂, with one end of the Tee suppling Ekosodin and the other end professors quarters. A butterfly valve is placed 5 m from the other end of the manifold to tanks T3 and T4 located at engineering and BDPA respectively. Draw a layout of the process described above, all tanks are fitted with relief valves. A line fitted with a relief valve rated 2,000 psi was pressure tested to 2,500 psi. Describe what would happen during the process of pressure test. If you were to handle this task, what would you do differently? A submersible pump is installed 400 ft in a well to supply water to a tank T₁ which is 1.5 m x 1.2 m x 1.5 m, and it is 16 m above the ground. The tank T₁ is to supply water to residents In Ekosodin, Professors quarters, BDPA and Faculty of Engineering. A pump P is installed on the line 10 m from the tank and a one-way valve is installed immediately after the pump. A manifold, with 3 shut-off valves is spotted 110 m from the pump. From one end of the manifold, a line is run to a tank T₂ which has a relief valve installed on it. A Tee is placed 10 m from Tank T₂, with one end of the Tee suppling Ekosodin and the other end professors quarters. A butterfly valve is placed 5 m from the other end of the manifold to tanks T3 and T4 located at engineering and BDPA respectively. Draw a layout of the process described above, all tanks are fitted with relief valves. A line fitted with a relief valve rated 2,000 psi was pressure tested to 2,500 psi. Describe what would happen during the process of pressure test. If you were to handle this task, what would you do differently? A submersible pump is installed 400 ft in a well to supply water to a tank T₁ which is 1.5 m x 1.2 m x 1.5 m, and it is 16 m above the ground. The tank T₁ is to supply water to residents In Ekosodin, Professors quarters, BDPA and Faculty of Engineering. A pump P is installed on the line 10 m from the tank and a one-way valve is installed immediately after the pump. A manifold, with 3 shut-off valves is spotted 110 m from the pump. From one end of the manifold, a line is run to a tank T₂ which has a relief valve installed on it. A Tee is placed 10 m from Tank T₂, with one end of the Tee suppling Ekosodin and the other end professors quarters. A butterfly valve is placed 5 m from the other end of the manifold to tanks T3 and T4 located at engineering and BDPA respectively. Draw a layout of the process described above, all tanks are fitted with relief valves. A line fitted with a relief valve rated 2,000 psi was pressure tested to 2,500 psi. Describe what would happen during the process of pressure test. If you were to handle this task, what would you do differently? A submersible pump is installed 400 ft in a well to supply water to a tank T₁ which is 1.5 m x 1.2 m x 1.5 m, and it is 16 m above the ground. The tank T₁ is to supply water to residents In Ekosodin, Professors quarters, BDPA and Faculty of Engineering. A pump P is installed on the line 10 m from the tank and a one-way valve is installed immediately after the pump. A manifold, with 3 shut-off valves is spotted 110 m from the pump. From one end of the manifold, a line is run to a tank T₂ which has a relief valve installed on it. A Tee is placed 10 m from Tank T₂, with one end of the Tee suppling Ekosodin and the other end professors quarters. A butterfly valve is placed 5 m from the other end of the manifold to tanks T3 and T4 located at engineering and BDPA respectively. Draw a layout of the process described above, all tanks are fitted with relief valves. A line fitted with a relief valve rated 2,000 psi was pressure tested to 2,500 psi. Describe what would happen during the process of pressure test. If you were to handle this task, what would you do differently?

Answer rating: 100% (QA)

Given scenario A submersible pump is installed 400 ft in a well to supply water to a tank T1 which i... View the full answer