Question: A system that lets engineers create the specification of new components using geometric modeling techniques is known as _ ( Blank ) _ . Question

A system that lets engineers create the specification of new components using geometric modeling techniques is known as _(Blank)_.
Question 12Answer
a.
midpoint subdivision
b.
computer-aided design (CAD)
c.
meteorological modeling
d.
queuing simulations

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

You are required to make a short summary of a proceeding paper below: A Tutorial on Simulation Conceptual Modeling by Stewart Robinson (2017) Using your creativity, write a 3 pages summary. Highlight...

Q:

Chapter 10 Business Process and Information Systems Development \"Jeff, we clean the clubhouse restrooms twice a day . . . in the morning before 7 and again just before lunch. We've been doing that...

Q:

MINI-PROJECT Implement a Software-Engineering Process stages by selecting any topic which is mention below or you can select your desired any other topic. Website Administration Airport checking-in...

Q:

A1 Software engineers use the following to enhance the quality of their products: 1. Tools II. Techniques III. Procedures IV. Paradigm A. I and II B. I, II and III C. I, II and IV D. I, II, III and...

Q:

Please read chapter 6 and answer the questions and see the ( guide to answer number 3) For each case study, you will view the material as the student's teacher, read the information provided and...

Q:

Please read chapter 5 and answer the questions and see the ( guide to answer number 3) For each case study, you will view the material as the student's teacher, read the information provided and...

Q:

Please read chapter 6 and answer the questions and see the ( guide to answer number 3) 1. Decide what assessment you would like to do to provide you with more information about the student, 2....

Q:

Please read chapter 8 and answer the questions and see the (guide to answer number 3) For each case study, you will view the material as the student's teacher, read the information provided and write...

Q:

Please read chapter 8 and answer the questions and see the ( guide to answer number 3) For each case study, you will view the material as the student's teacher, read the information provided and...

Q:

Hello , please answer this question reading the pdf. \begin{tabular}{l|l|l|l|l} What are sources of requirements cha nges on the JUSS scenario / your experiences? & What data would be impacted by the...

Q:

Royston starts his own business on 1 September, operating as a wholesaler of novelty goode His transactions during September were as follows: Transfers 750 of his savings into a business bank...

Q:

If f R[a, b] and c R, we define g on [a + c, b + c] by g(y) := f(y - c). Prove that g R[a + c, b + c] and that b+ca+c g = ba f . The function g is called the c-translate of f.

Q:

Your answer is partially correct. The adjusted trial balance for Sheridan Farm Corporation at the end of the current year contained the following accounts. Prepare the long - term liabilities section...

Q:

Compared with half a century ago, adoption has become _ _ _ _ _ _ _ _ _ common, but it is more open and acceptabl e , so we probably discuss it _ _ _ _ _ _ _ . fill in the blanks more or much less or...

Q:

4. Once the tasks have been identified, it is important to identify the knowledge, skills, or abilities necessary to successfully perform each task. This information can be collected through...

Q:

5. Go to wdr.doleta.gov/SCANS/, a Web site for the U.S. Department of Labor Employee and Training Administration that includes reports of the SCANS commission (Secretarys Commission on Achieving...

Q:

9. Review the accompanying sample tasks and task ratings for the electronic technicians job. What tasks do you believe should be emphasized in the training program? Why?