Question: after running the program what will be output on portb with a voltage of approximately 5 5 0 mv on ADC 4

after running the program what will be output on portb with a voltage of approximately 550mv on ADC4

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

Write a C-program that reads in a 20Hz sine wave with an amplitude of 1V (rms) through ADC0 channel and writes out its derivative at DAC0 channel. Use a sampling frequency of 750 Hz. Use the...

Q:

Appendix G: (Not required information but I put it here incase it might help) b. Build a Simulink program based on the transfer function in Eq. (2-8) with R= 10k12 and C = 10uF. to conduct...

Q:

Why is there a risk of data and control hazards in a pipelined processor? For modern RISC instruction set architectures like RISC-V, why are control hazards not exposed in the programming model? [4...

Q:

ITU Control & Automation Eng. Dept. KON 3 0 9 E Microcontroller Systems Experiment 4 : ADC and USART Construct the circuit as shown in the Figure. Check your wiring and make sure that no connection...

Q:

The MAX31855 is the amplifier and the ADC of the thermocouple used in a lab. The listed specifications indicate that it is a 12 bit ADC with an amplified gain output of -100 to +100mV. What is the...

Q:

1. Write a program to output a saw tooth voltage from the myRio DAC and read it in on the myRIO ADC. Use custom FPGA for this and write one program on the FPGA (should be very simple) and another on...

Q:

Construct the circuit as shown in the Figure. Check your wiring and make sure that no connection is made to the 5 V supply. The ADC peripheral should be configured to sample CH 0 and CH 1 using...

Q:

The sensor s output voltage can be digitized with one of the ADC channels in the MCU. The ADC has a maximum of 1 4 bits of resolution, providing 1 6 , 3 8 4 levels of voltage digitization. The...

Q:

Answer the following true/false questions To get maximum resolution, the clock required for the ADC should be in the range 50 200KHz (T / F) For 8-bit timers, the maximum count is always equal to the...

Q:

013 Which of the followings are buses? USB. SCSI.(RS232. ADC (GPIO Q14- 1. What shall be the type of port at the setup flow if roll is connected to a button switch, and the other terminal of switch...

Q:

The Acme Bus Company has a daily ridership of 18,000 passengers and charges $1.00 per ride. The company wants to raise the fare yet keep its revenue as large as possible. (The revenue is found by...

Q:

Use MATLAB to find the voltages at nodes a, b, c, and d in the circuit of Fig. 3.77. Figure 3.77 AST 91

Q:

What may be responsible for any significant discrepancy? The discrepancies that you observe are they systematic or statistical? Explain.

Q:

Features of Internet Marketing of Web 3.0( ) A. Any channel, any device, anywhere-Bring your own everything B. The human way to interact with technology C. 3 D print at home D. Internet of Thing(IOT)...

Q:

=+11. Use connectorsThese are words that tie each sentence or paragraph to the next, like and, so, the truth is, naturally, etc. Think of them as little stepping-stones that create a path that leads...

Q:

=+slogan Good to the last drop, the closing line could read, One sip and you'll know why it's good to the last drop. The closing line doesn't have to repeat the headline word-for-word, just embody...

Q:

=+9. Consider parallel construction This is a specific kind of phrasing or wording that you've heard or read many times: To be or not to be. It's not just coffee. It's Starbucks. No salt. No sugar....