Question: What force (kip) is required to punch a square hole with 2 inch on each side through a 3/8 inch thick plate if the ultimate

What force (kip) is required to punch a square hole with 2 inch on each side through a 3/8 inch thick plate if the ultimate shearing strength of the plate is 42 ksi? Factor of safety is 4.

Step by Step Solution

★★★★★

3.40 Rating (153 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Answer The force required to punch a square hole with 2 inch ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

What are BANs, RANs, and TANs? Why are they accounted for differently?

On 1 January 2019 JGoo Ltd acquired 100% of JBLee Ltd for Ksh.1 billion when JBLee Ltds share capital & reserves amounted to Ksh.700 million. The fair value of JBLee Ltds assets & liabilities...

What are megabore open tubular columns? Why are they used?

What is the force required to punch a square hole, 150-mm on each side, from a 1-mm-thick 5052-0 aluminum sheet using flat dies? What would be your answer if beveled dies were used instead?

You want to fluidize a bed of solid particles using water. The particles are cubical, with a length on each side of $1 / 8$ in., and a SG of 1.2 . (a) What is the sphericity factor for these...

A steady push on the piston in Fig P6.22 causes a flow rate Q = 0.15 cm3/s through the needle. The fluid has ρ = 900 kg/m3 and μ = 0.002 kg/ (m⋅s). What force F is required to maintain...

Suppose the hand in Problem 32 holds a 15-kg mass. What force, Fm, is required of the deltoid muscle, assuming the mass is 52cm from the shoulder joint?

A rope of length L and mass per unit length of lies coiled on the floor. (a) What force F is required to hold one end of the rope a distance y

Truss members supporting a roof are connected to a 26-mm-thick gusset plate by a 22 mm diameter pin as shown in the figure and photo. The two end plates on the truss members are each 14 mm thick. (a)...

A standard brick (dimensions 8 in. Ã 4 in. Ã 2.5 in.) is compressed lengthwise by a force P, as shown in the figure. If the ultimate shear stress for brick is 1200 psi and the ultimate...

A 20.0 2 bulb is connected across the terminals of a 12.0 V battery having 3.00 of internal Roview Co resistance. Part A For related problem-solving tips and strategies, you may want to view a Video...

3. A weak acid is 0.01% ionised in 0.1 M solution. Its ionisation constant is: 1) 10-5 2) 106 3) 108 4) 10-9

13 Round the number 530.403977 to the stated number of significant figures (s.f.). a 1 s.f. d 4 s.f. b 2 s.f. e 5 s.f. 3 s.f. f 6 s.f.

A block of mass m is given an initial velocity by the spring. The spring has a spring constant k, and is squeezed 0.200 m when the block is at point A. There is no friction in the system EXCEPT for...

Calculate the following ratios from the data given below: 1. Debt ratio 2. Debt service coverage multiples 3. Interest coverage Balance Sheet 12/31/2014 Assets Cash..$575,000 Short-term...

We had been doing our training in California at the same site for about four years when we first request to produce our weeklong training in Illinois. The group that funded the event chose a...

E2) If expenses in year 1 amounted to 430 000 and the salary ratio year 1 to year 2 was 5:6, how large was the EBITDA (Earnings Before Interest, Taxes, Depreciation and Amortization) in year 2?(1...

4-81. Two couples act on the frame. If d = 4 ft, determine the resultant couple moment. Compute the result by resolving each force into x and y components and (a) finding the moment of each couple...

Which part of the research paper do you find the following? It must also reflect the variables under study. Question 9 Select one: a. Statement of the Problem b. Scope and Delimitations c. Research...

Please if you well not give solution don't answer. I need only solution not explanation I solve part 1 and 2. I only need solution for part3 ) Supplement lab activity "'\"\\' gl THE EMIRATES...

Pittman Company is a small but growing manufacturer of telecommunications equipment. The company has no sales force of its own; rather, it relies completely on independent sales agents to market its...

Hypothetical Company Project AUTO FORCE Ltd is an automation firm that invests much in research and development ( R&D ) before releasing new equipment, typically designed to save labour time. AUTO...

ANSWER ALL THE QUESTIONS Question 1 Khaki & Sons Limited (KSL) is a family business that deals in car spare parts. It is one of the largest dealers in car spare parts in Uganda. Since inception in...

ISSUES IN ACCOUNTING EDUCATION Vol. 26, No. 3 2011 pp. 521-545 American Accounting Association DOI: 10.2308/iace-50031 Breach of Data at TJX: An Instructional Case Used to Study COSO and COBIT, with...

The force needed to remove the cap from a medicine bottle is an important feature of the product because requiring too much force may cause diffi culty for elderly patients or patients with arthritis...