Question: As shown, water (15C) is flowing from a tank through a tube and then discharges to the ambient air. The tube has a diameter of

As shown, water (15°C) is flowing from a tank through a tube and then discharges to the ambient air. The tube has a diameter of 8 mm, a length of L = 6 m, and the resistance coefficient is f = 0.015. The water level is H = 3 m. Find the exit velocity in m/s. Find the discharge in liter/sec. Sketch the HGL and the EGL. Assume that the only head loss occurs in the tube as friction

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Given that the only loss is due to friction in the tube we can make use of the Bernoullis equation and DarcyWeisbach equation First lets understand th... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

As shown, water (15C) is flowing from a tank through a tube and then discharging to ambient. The tube has an ID of 8 mm and a length of L = 6 m, and the resistance coefficient is f = 0.015. The water...

5-180 Determine the power input for a compressor that compresses helium from 150 kPa and 20C to 400 kPa and 200C. Helium enters this compressor through a 0.1-m2 pipe at a velocity of 15 m/s. 5-181...

81C How does reversible work differ from useful work? 82C Under what conditions does the reversible work equal irreversibility for a process? 83C What final state will maximize the work output of a...

Combustion air in a manufacturing facility is to be preheated before entering a furnace by hot water at 90C flowing through the tubes of a tube bank located in a duct. Air enters the duct at 15C and...

Repeat Prob. 7108 for staggered arrangement with S L = S T = 6 cm. Data from problem 108 Combustion air in a manufacturing facility is to be preheated before entering a furnace by hot water at 90C...

#6 and #7 1. Moist air at standard conditions is at a dry bulb temperature of 50F and a relative humidity of 70%. It is sensibly heated (constant moisture) to 72F. Use the psychrometric chart to...

Chapter 7: Wastewater Management IN THIS CHAPTER U.S. wastewater regulations Sources of contamination of wastewaters Classification of water pollutants Characteristics of wastewater Wastewater...

1)solve all questions either i will dislike Data Data Q2) Calculate the overhead flow rate in kmoles/s (shell side)? Calculate the flow rate for each compound in kg/s and kmoles/s Assuming the wt%...

3-1C W hat is the difference between saturated liquid and compressed liquid? 3-2C What is the difference between saturated vapor and superheated vapor? 3-3C Is there any difference between the...

Lab #13 Speed of Sound Purpose The purpose of this lab is to explore resonance to calculate the speed of sound in air Introduction A wave is a disturbance that travels through a medium, transporting...

Suppose that you are organizing the game described at the end of Section 2.3.1, where you charge players $2 to roll 7 two dice and then you pay them the difference in the scores. What is the variance...

From Equation 8.19, if the logarithm of is plotted versus the logarithm of ?, then a straight line should result, the slope of which is the stress exponent n. Using Figure 8.31, determine the value...

Silk Textures sells a line of women's dresses. The company uses flexible budgets to analyze its performances. The firm's performance report for November is presented below: ActualBudgetDresses sold 5...

(d) Explain which of the following exist as improper Riemann integrals (justify your answer in each case by reference to relevant theorems or by other appropriate rigorous arguments). (ii) ), (sin())...

Cross-Cutting Global Health Issues - Current Threats to Global Health, Part 1 Readings: Urgent health challenges for the next decade (WHO, 2020):...

A reference value involves comparing the costs and benefits ofMultiple Choicesubatitute items.Bems of equal or greater value.products weth which a consumer is familiar and ilems the consumer has not...

At a point on the surface of a machine component, the stresses acting on the x face of a stress element are (x = 5900 psi and Txy = 1950 psi (see figure). What is the allowable range of values for...

A wood column of rectangular cross section (see figure) is constructed of structural grade, Douglas fir lumber (Fc = 12 MPa, E = 10 GPa). The cross-sectional dimensions of the column (actual...

The cross section of a steel beam is shown in the figure. This beam is subjected to a bending moment M having its vector at an angle Î¸ to the z axis. Determine the orientation of the...

The simple Poisson process of Section 3.6 is characterized by a constant rate at which events occur per unit time. A generalization of this is to suppose that the probability of exactly one event...

7. In Exercise 2, find the expected payoff and the expected loss of each action, and find the action which has the largest expected payoff and smallest ex pected loss, given that the probabilities of...

The mode of a discrete random variable X with pmf p(x) is that value x* for which p(x) is largest (the most probable x value). a. Let . By considering the ratio , show that b(x; n, p) increases with...