Question: Assuming a 4-bit ADC is sampling at a frequency 100 Hz and the overhead time of acquiring the signal is negligible, what is the maximum

Assuming a 4-bit ADC is sampling at a frequency 100 Hz and the overhead time of acquiring the signal is negligible, what is the maximum time the microcontroller's code can take to execute before the next sample must occur? 100 10 s 015 0.01 s 0.1 s

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

EET 412 2017-1 1. The number of different possible binary PCM values that can be encoded with 5-bit words is (a) 16 (b) 5 (c) 64 (d) 32 2. An analog signal is to be encoded with at least 2000 values....

Consider the following context-free grammar of expressions E ::= n | (E, E) where n ranges over integers. (a) Present a right-most derivation of the expression ((21, 18), 17). [2 marks] (b) List the...

I need help with Part 2 the MATLAB part. Here is the code for the for the below picture: int pot = A0; int val = 0; int val7 = 0; int val4 = 0; void setup() { Serial.begin(9600); Serial.flush(); }...

How many numbers of comparators and resisters are required to implement a 3 - bit ADC circuit? Calculate the resolution of 5 - bit ADC for a full - scale voltage of 1 V . b . How many numbers of...

Q3.Suppose each bit change in a 4-bit ADC represents a level of 10.7m. What would the decimal number corresponding to the 4- bit be for a level of 0.4m?What's the binary 4-bit number output...

If a 2 - bit ADC is replaced by a 4 - bit ADC in a system, by what factor will the delta value ( amplitude quantized voltage ) decrease i . e . , 2 - b i t A D C 4 - b i t A D C ? A designer wishes...

4. Text book problem 1.11 and 1.12 (20 pt.) 1.11 Asignal is sampled every 1 ms for 20 ms, with the following "true" values of the analogue voltage at successive sampling times. Plot the values of the...

Assume a 4-bit ADC (of 16 steps in the analog range) uses the Successive Approximation implementation. The input voltage range of the ADC is OV-32V. If the input is 20V, how does the ADC work out...

The successive approximation ADC has been the mainstay of data acquisition systems with the clock rate of 4 M H z . Successive Approximation Register ( SAR ) supplies an approximate digital code to...

Matlab DSP 02/ Assuming that a 4-bit ADC channel accepts analog input ranging from 0 to 10 volts, determine a. The number of quantization levels; b. The step size of the quantizer or resolution; c....

Tablet Company purchases $20,000 of devices for resale. The company also spends $500 in transportation cost to have the devices shipped from the supplier, $2,000 in labour and parts to upgrade the...

TASK 4 a) WEEK 9 Supplementary information is provided for the EOM adjusting journals to be entered in the General Journal. Required; Record the EOM adjustments and complete the Closing Journal...

XYZ Paper Mill purchases a 5 - year special insurance paying a benefit in the event itsmachine breaks down. If the cause is minor ( 1 ) , only a repair is needed. If the cause ismajor ( 2 ) , the...

Assuming that pessimistic locking is being used but the two-phase locking protocol is not, create a chronological list of the locking unlocking and data manipulation activities that would occur...

4. Discuss the strengths and weaknesses of different evaluation designs.

1. Develop a questionnaire to measure the degree to which the work environment supports transfer of training. Include the questions and the rating scales you would use. Use the checklist in Table 5.5...

5. Choose the appropriate evaluation design based on the characteristics of the company and the importance and purpose of the training.