Question: b . A beam with 2 m long is subjected with uniformly distributed load of 2 0 k N m along the beam as shown

b. A beam with 2 m long is subjected with uniformly distributed load of 20kNm along the beam as shown in Figure 2. Given E=200GNm2, determine the maximum slope and deflection of beam.
20kNm
A
b . A beam with 2 m long is subjected with

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A beam AB 2 m long and carrying a uniformly distributed load of 15 kN/m is resting over a similar beam CD 1 m long as shown below and finds a reaction at C. A beam AB 2 m long and carrying a...

Q:

3 . 7 FIGURE below shows a light horizontal beam ABCDEF of a uniform cross section, loaded as shown: 3 . 7 . 1 Calculate the reaction at the supports? 3 . 7 . 2 Draw a shear - force diagram, using a...

Q:

1 . ( a ) An inclined ( 8 = 4 5 \ deg ) simple beam is subject to a uniformly distributed load g along AB as shown in Figure 1 ( a ) . The total magnitude of vertical load is gL . ( i ) Draw the...

Q:

( 1 0 0 MARKS ) There are FIVE ( 5 ) questions in this paper. Answer ALL Questions in the Answer Booklet. The overhang beam EACDB was subjected to uniformly distributed load and point loads as shown...

Q:

Q 2 : A simply supported beam is subject to uniformly distributed load q along CD as shown in Figure 2 . ( a ) Draw the shear force diagram ( SFD ) with the sign labels and pertinent values. Note...

Q:

Q3 A horizontal beam BC is subjected to uniformly distributed load, w and at the same time it is supported at end B by a column AB (diameter of 50 mm) as shown in Figure Q3. Assume that all bars are...

Q:

I. Calculate the minimum and maximum moments. II. Derive the equations for the top and bottom fiber considering the strength at transfer stage. III. Derive the equations for the top and bottom fiber...

Q:

MATLAB CODE LANGUAGE I need help with part 3 & 4 the equations and the plotting ENGI 1331: Mastery Assignment #4 Background lhis problem will introduce you to a simple example of a simply supported...

Q:

Final Name Surname: Student iD 2 0 2 2 - 2 0 2 3 Fall Semester - Duration: 1 0 0 minutes Course Nathe : cvin 2 2 2 - Mechanics of Mroup: . . . . . Date! ( 3 0 9 5 ) A WT 2 0 5 3 0 structural steel...

Q:

Question points ] The built - up beam shown in Figure 2 is subjected to uniformly distributed load w = 1 0 k N m and has span length l = 1 0 m . Assume E 3 5 0 steel and weld ultimate strength as 4 0...

Q:

Reporting an investment at its fair value means adjusting its carrying amount for changes in fair value after its acquisition (or since the last reporting date if it was held at that time). Such...

Q:

Patterson Awning manufactures awnings and uses a standard cost system. The company allocates overhead based on the number of direct labor hours. The following are the companys cost and standards...

Q:

When deciding to purchase a stock, you should base your decision on the expectations of the corporation's future earningsthe movement of the stock marketa good investor's meetingmeeting the owners....

Q:

Direct Practice Improvement (DPI) Manuscript: Preliminary Pages and Chapter 1 - Introduction to the Project