Question: Between a-b,connecting a load impedance should be maximum power. Find the Vth of a-b. ZTh , ZLmax and PLmax should be calculated. Deure Ik W

Deure Ik W =21 radls VK: 5+j(S) V.H C= 13.103 F Ik=-2+j

Between a-b,connecting a load impedance should be maximum power.

Find the Vth of a-b.

ZTh , ZLmax and PLmax should be calculated.

Deure Ik W =21 radls VK: 5+j(S) V.H C= 13.103 F Ik=-2+j (3) Amp a-b arasna baplanacak olan yeh empedan Sindan azamipG Gekilmesi isteniyor. a-b arasndaki esdeper Thevenin deuresini bulunuz UtH=? a - Baplanacak yok empedansin ve Gekecepi pice bulunuz. ZTH=? 2Lmax=? , Pemox =? (Hassasiyet en az 10-4 olmal)

Step by Step Solution

★★★★★

3.46 Rating (156 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

The Thevenin impedance of a source is ZTh = 120 + j60 , while the peak Thevenin voltage is VTh = 110 + j0 V . Determine the maximum available average power from the source.

A load with impedance ZL = (25 = J50) is to be connected to a Lossless transmission line with characteristic impedance Z0, with Z0 chosen such that the standing-wave ratio is the smallest possible....

A three-phase load impedance consists of a balanced wye in parallel with a balanced delta. What is the equivalent wye load and what is the equivalent delta load if the phase impedance of the wye and...

Q . 4 . Find load impedance to transfer maximum power and maximum power to the load. [ Hint: use delta to star transformation ( i . e . \ ( \ Delta \ ) Y ) ] .

1 . Ask the user to input the type and geometry data of any lossless transmission line and output C , L , and the characteristic impedance of the line. 2 . Design for a microstrip transmission line...

A pulpwood loader as shown in Figure P5-63 is to be designed to lift 2.5 kip. Select a steel and determine a suitable tubular cross section for the main upright member BF that has attachments for the...

A loaded beam ABCDE is simply supported at B and D and carries point loads of 40 kN, 80 kN, and 60 kN at A, C, and E respectively, together with a uniformly distributed load of 20 kN/m between B and...

TASK3 OBJECTIVE: Write a function to do useful computation. You should work on this task individually, but you may discuss results with your teammates Write a function to perform linear interpolation...

SEND: Work for Submission for Week 1 Show the essential working in the spaces provided for ALL questions. 1. To the nearest metre, the length of cable that would connect the roofs of two buildings...

By utilizing Multisim simulation, measure the rms values of the phasor TRy, representing the voltage across the load Ru and the phasor repre - senting the current I R , through the load Ru . Remove...

For acquiring an asset, what are the key advantages of leasing as compared to borrowing? What are the key disadvantages of leasing?

As operations managers we try to improve our ways of measuring and allocating our labor and raw material costs to our product or service. Why is this important ? What types of costs are the most...

OLTP is the acronym for a . Online Transact Process. b . Offline Transaction Processing c . Online Transaction Processing d . Online Transacting Product.

Explain the difference between Alternating Direction Method of Multipliers(ADMM) and coordinate descent (CD) .

Find the derivative of the function. y = O y'=. 24 O y'= a-24 (x - Ptx- IR O y'= O y'= (x- 3Px - 1P

Explain following experimental terminologies & concepts. Demonstrate your understanding by providing illustrative examples (must) for each of them . a) The method of steepest ascent and reasons of...

Find the integral x.dx as the LIMIT OF A SUM (please don't just simply integrate). Given upper limit is 'b' and the lower limit is 'a'.

A local consulting firm employes 30 full time staff. the budgeted compensation per employee is $50 000, for 2000hours. all direct labour costs are charged to clients. any other costs are included in...

If management sought to transfer 10 thousand units of Beta's production to Alpha, the firm's overall profits would increase decrease not change , since for those 10 thousand additional units MC...

a) Design a single stage common emitter amplifier using a 2N5089 npn transistor. You should adopt a 4 resistor style configuration. The amplifier is required to provide linear amplification. The...

For problems 1 and 2, you need to clearly indicate your answers on Smith charts in order to receive full credit. Do not solve more than 1 problem using a single Smith chart. 1. (3 pts) Design a...

Locate impedance and find admittance. In this part normalize a given impedance to transmission line with characteristic impedance Zo = 5 0 , locate on Smith chart and determine the equivalent...

Electromagnetism (2) Smith Chart Matching One technique to achieve matching in transmission lines is to connect a piece of transmission line (either short circuited or open circuited) at certain...

Reconsider case (b) of Problem 10.5. Let the load impedance $4.9+j 0.5 \Omega$ be the input impedance to a $\mathrm{CO}-7$ induction disc time-delay overcurrent relay. The CO-7 relay...

Your circuit will be a source of 120/0 for the a phase, at 60 Hz. Your source impedance is 0.1 + j0.4. The line impedance is 2.9 + j1.6. The load impedance is 77 +j58. Both source and load are in a...