(c) From a tensile stress-strain behaviour of cylindrical stainless steel SS318 (diameter of 9.0 mm and...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
(c) From a tensile stress-strain behaviour of cylindrical stainless steel SS318 (diameter of 9.0 mm and initial length of 310 mm) shown in figure below, determine the following: Ultimate tensile strength. Young's Modulus.. Yield strength at strain offset of 0.002. Maximum load that can be sustained by stainless steel SS318. Percentage of elongation if the final length after failure is 370 mm. (0) (ii) (iii) (iv) € Stress [MPa] 60 50 40 30 20 10 0 0.00 0.25 0.50 Stress [MPa] g 2 ........ 10 0:00 Strain 0:75 0.005 1.00 1.25 (10 marks) (c) From a tensile stress-strain behaviour of cylindrical stainless steel SS318 (diameter of 9.0 mm and initial length of 310 mm) shown in figure below, determine the following: Ultimate tensile strength. Young's Modulus.. Yield strength at strain offset of 0.002. Maximum load that can be sustained by stainless steel SS318. Percentage of elongation if the final length after failure is 370 mm. (0) (ii) (iii) (iv) € Stress [MPa] 60 50 40 30 20 10 0 0.00 0.25 0.50 Stress [MPa] g 2 ........ 10 0:00 Strain 0:75 0.005 1.00 1.25 (10 marks)
Expert Answer:
Answer rating: 100% (QA)
Soution Partias vitimate tensile Strength Imant Part bc youngs mudul... View the full answer
Related Book For
Materials Science and Engineering An Introduction
ISBN: 978-1118324578
9th edition
Authors: William D. Callister Jr., David G. Rethwisch
Posted Date:
Students also viewed these mechanical engineering questions
-
Determine the maximum column load that can be applied on a 1.5 m 1.5 m square foundation placed at a depth of 1.0 m within a soil, where = 19.0 kN/m 3 , c' = 10 kN/m 2 , and ' = 24. Allow a factor...
-
The 3-span continuous beam shown in Figure below has to support the loads shown with a collapse factor of ? = 1.4. Investigate the collapse of each span and determine the corresponding plastic moment...
-
An insulated piston-cylinder device shown in figure below initially contains 1.8-kg saturated liquid water at 120oC. Now an electric resistor placed in the tank is turned on for 10 min until the...
-
In Exercises 5 and 6, the transition matrix P for a Markov chain with states 0 and 1 is given. Assume that in each case the chain starts in state 0 at time n = 0. Find the probability that the chain...
-
Assume the following additional information about the use of financial derivatives for the operational audit described in Problem 19-51: 1. Company policy limits financial derivatives strictly to...
-
1. What type of attitude scale is used by the ACSI if any? 2. What type of attitude study might you design if you were the consultant? 3. How would you use results from this approach to diagnose...
-
What are the different ways a deposition summary may be prepared?
-
A six-column table for JJW Company follows. The first two columns contain the unadjusted trial balance for the company as of July 31, 2011. The last two columns contain the adjusted trial balance as...
-
Case study: Impact of writeoff / writedown on economics Applying the economic analysis model of ATCF to evaluate the impact of writeoff/writedown on project economics. A simplified economic analysis...
-
Using the following information on Rockboro Case please answer the following Question: What are the problems here, and what do you recommend and what are the implications of different payout levels...
-
The preliminary annual accounts of X company show a profit before tax of USD 15 000 000. Other operating expenses include USD 200 000 in non-deductible representation expenses and the expensing of...
-
Perform the indicated operations and simplify completely: (x+9) - (x+5) Answer: =
-
Estimate the limit 4 -1 lim- x0 cosx1
-
Use the five features of social media to describe a social media platform. Explain the benefits of using a social media strategy. Measures of Effectiveness: Develop responses to the following that...
-
Air at a temperature of 300 C flows with a velocity of 10 m/s over a flat plate 0.5 m long. Average Nusselt number to maintain plate-surface temperature at 27 C is calculated to be 57.4 by the...
-
3. (5 points) Based on the inflation rate given, compute the amount of money that Jimmy and Jane expect they will need to live on during their first year of retirement in 35 years.
-
Amy is creating and implementing her new financial action plan. As a result, she asks for more hours at work and she begins to save more money. Why is she doing this? Multiple choice question. Amy...
-
Find the intercepts and then graph the line. (a) 2x - 3y = 6 (b) 10 - 5x = 2y
-
On the basis of the photomicrograph (i.e., the relative amounts of the micro constituents) for the iron-carbon alloy shown in Figure 9.30 and the Fe-Fe3C phase diagram (Figure 9.24), estimate the...
-
Determine the modulus of resilience for each of the following alloys: Use the modulus of elasticity values in Table 6.1? Yield Strength Material MPa psi Steel alloy Brass alloy 830 120,000 380 55,000...
-
The following figure shows the tensile stress-strain curve for a plain-carbon steel. (1) What is this alloy's tensile strength? (A) 650 MPa (B) 300 MPa (C) 570 MPa (D) 3,000 MPa (2) What is its...
-
The \(T d S\) equation \(T d S=C_{P} d T-T\left(\frac{\partial V}{\partial T} ight)_{P} d P\) is valid where entropy is a function of (a) \(T\) and \(P\) (b) \(P\) and \(V\) (c) \(T\) and \(V\) (d)...
-
The inversion temperature of hydrogen is (a) \(315 \mathrm{~K}\) (b) \(202 \mathrm{~K}\) (c) \(275 \mathrm{~K}\) (d) \(345 \mathrm{~K}\).
-
The inversion temperature of helium is (a) \(460 \mathrm{~K}\) (b) \(40 \mathrm{~K}\) (c) \(620 \mathrm{~K}\) (d) \(823 \mathrm{~K}\).
Study smarter with the SolutionInn App