Question: Compute the stress components on the 30 plane at point B of the cantilever beam. Assume that x = 300 mm. Show the results on

Compute the stress components on the 30° plane at point B of the cantilever beam. Assume that x = 300 mm. Show the results on a properly oriented element.

20 mm 30 B 20 mm 50 KN 20 mm 120 mm

Step by Step Solution

★★★★★

3.58 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Step 111 Draw the free body diagram of the beam 300 Step 211 1 Calculate the polar moment of inertia ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Accounting Questions!

The management of the Dynaco manufacturing plant wants to connect the eight major manufacturing areas of its plant with a forklift route. Because the construction of such a route will take a...

Two forces are applied at point B of beam AB. Determine the magnitude and direction of their resultant using the triangle rule. B 3kN 40 2 kN

A cantilever beam of W 12 x 14 section and length L x 9 ft supports a slightly inclined load P x 500 lb at the free end (see figure). (a) Plot a graph of the stress ÏA at point A as a function...

The components of plane stress at a critical point on a thin steel shell are shown. Determine if failure (yielding) has occurred on the basis of the maximum distortion energy theory. The yield stress...

An element in plane stress is subjected to stresses (x = 5700 psi and Txy = - 2300 psi (see figure). It is known that one of the principal stresses equals 6700 psi in tension. (a) Determine the...

An element in plane stress is subjected to stresses (x = - 50 MPa and Txy = 42 MPa (see figure). It is known that one of the principal stresses equals 33 MPa in tension. (a) Determine the stress (y....

An element in plane stress on the surface of an automobile drive shaft is subjected to stresses of x = -45 MPa and xy = 39 MPa. It is known that one of the principal stresses equals 41 MPa in...

An idealized radial turbine is shown in Fig. P11.90. The absolute flow enters at 25° with the blade angles as shown. The flow rate is 8 m3/s of water at 20°C. The blade thickness is constant...

A conducting rod of length ? rotates at constant angular velocity about one end, in a plane perpendicular to a uniform magnetic field B?(Figure). (a) Show that the magnetic force on a charge q?at a...

Consider the market shown in the graph below. a. Compute the consumer surplus. b. Compute the producer surplus. Now assume that government puts a price floor on this product at $20 a unit. c. Compute...

Nine work centers must be located in a square building (3x3 layout). The locations of centers 1, 2, 3, and 4 are fixed as shown in Table 4.7 (on page 140). Assuming that transportation costs are $1...

Banc Corp. Trust is considering a bank-wide overhead rate or departmental overhead rates to allocate $360,000 of indirect costs. The bank-wide rate could be based on direct labor hours (DLH) or the...

Your friend Isaac is 40 years old. He is married to his wife Madison and they have 3 small children. Both Isaac and his Madison have good paying jobs and are comfortable financially. Isaac has life...

f ( x ) = 9 l n ( 3 4 x 2 ) f ' ( x ) =

10 12 A = * -5 Note that the middle row of A is not given. Which of the following could be an eigenvector of A? A) (1,0,1)7 (B) (3,0,1) (C) (6,0,1)7 (D) (4,0,1)T (E) (5,0,1)T (F) (2,0,1)7 (G)...

The augmented matrix for a linear system is given below. The asterisks represent unspecified real numbers. What kind of solution does the system have? (Answer 'inconclusive' if there is not enough...

Let A be an n x n matrix. Consider the following statements. (i) Ax = 0 has nontrivial solutions. (ii) A can be expressed as a produet of elementary matrices. (iii) 2 = 0 is an eigenvalue of A. (iv)...

Find the entry in row 3, column 3 of A1. (i.e., if B = A, find b33.) Let 9 6i 2 + i 7+ i c - 5i A i 1/5

calculate based on the maps highest to lowest risk for A-F \f

The allowable bending stress for the bar is Ï allow = 200 MPa. Determine the maximum moment M that can be applied to the bar. 80 mm 20 mm 10 mm 10 mm 10 mm

The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN m is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress...

The man has a mass of 100 kg and center of mass at G. If he holds himself in the position shown, determine the maximum tensile and compressive stress developed in the curved bar at section aa. He is...

You are given the following set of data: y x1 x2 x3 45 40 41 39 41 31 41 35 43 45 49 39 38 43 41 41 50 42 42 51 39 48 40 42 50 44 44 41 y x1 x2 x3 45 42 39 37 43 37 52 41 34 40 47 40 49 35 44 44 45...

The following data represent a dependent variable and four independent variables: y x1 x2 x3 x4 61 37 13 10 21 37 25 7 11 32 22 23 6 7 18 48 12 8 8 30 66 34 15 2 33 y x1 x2 x3 x4 69 35 19 9 23 24 23...

A regression equation to be used to predict a dependent variable with four independent variables is developed from a sample of size 10. The resulting equation is 32.8 0.470x1 0.554x2 4.77x3 0.929x4...