Question: Consider the beam shown below. There is a hinge at point B ( zero - moment points ) . There is a point load of

Consider the beam shown below. There is a hinge at point B(zero-moment points). There is a point load of P=3kN and a uniform load of w=12.6kNm that can move on any part of the beam. Take L=5.6m. Calculate the upward reaction due to the moving loads at point C . Present your answer in kN unit with two decimal points.
Consider the beam shown below. There is a hinge

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Consider the beam shown in Figure P5.12. (a) Write the equations for shear and moment using an origin at end A. (b) Using the equations, evaluate the moment at section 1. (c) Locate the point of zero...

Q:

The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a single live load of 40 k and (c) the maximum positive shear at E. Assume A and C are rollers, D is a pin, and...

Q:

Consider the beam assembly shown below Two horizonal beam member A B and B D are connected by a double shear pin at B Note that points A and D are a simple roller and pinned supports respectively A 1...

Q:

Determine the internal reactions at Point E in the beam. Note that there is a hinge at Point C, but not at Point E. Point E is located halfway between points A and B. The support at A is able to...

Q:

The contimuous beam shown below has a distributed load appliod over span B C and a point load applied at joint D . The steel beam ( E - 2 9 0 0 0 lssi ) has secood moment of area f - 6 0 0 inch 4 ....

Q:

Cross section 5 feet from the right end of the beam. Use this drawing for Parts a - d . \ ( \ checkmark \ ) Point B - Located just below the top rail on the outer surface 3 a ( 1 0 points ) :...

Q:

Question 3 : ( 2 0 points ) Figure 3 shows a beam system consisting of two beams AB and BD . Beam AB is fixed at the left end A . Beam BD is supported by a roller at the right end. Beams AB and BD...

Q:

Consider the beam shown in (Figure 1). Suppose that the distributed load intensities w = 80 lb/ft and W2 35 lb/ft. Follow the sign convention. = Figure 1 of 1 12 ft -15 f D 690 lb SA1 10 ft Determine...

Q:

Hand written solution required Consider the beam shown in [E gute 1) Take Part A w/ = 12 kip/ft Follow the sign convention Determine the normal force al point c Express your answer in kilopounds to...

Q:

Solve this question from a Systems Analysis worksheet Fig. 1 1 shows an alignment system being considered for directing a beam of microwave power onto a satellite in orbit. A rigid parabolic...

Q:

The cafeteria in a building offers three different lunches. The demands for the three types of lunch on any given day are independent and Poisson distributed with means 4.85, 12.70, and 27.61. The...

Q:

22. A body is vibrating with simple harmonic motion of amplitude 15 cm and frequency 4 Hz. Compute a. the maximum values of the acceleration and the velocity b. the acceleration and velocity when the...

Q:

An example of a specialty component of an AIS is Property, plant and equipment Sales Journal Subsidiary ledger Voucher Cheque Register

Q:

Department S had 700 units 62% completed in process at the beginning of the period, 8,100 units completed during the period, and 1,000 units 39% completed at the end of the period. What was the...