Question: D ) A riveted lap joint is shown below. The rivets are 1 0 mm diameter and have an ultimate shear stress of 4 0

D) A riveted lap joint is shown below. The rivets are 10 mm diameter and have an
ultimate shear stress of 400Mn/m2. If a factor of safety of 5 is applied, find the maximum
load that can be carried.
D ) A riveted lap joint is shown below. The

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

For eccentric loaded riveted joint as shown in the figure with x = 100 mm and permissible shear stress of 60 MPa, determine the diameter of the rivets in mm. X 50mm 50kN + (a) 24 mm (c) 21 mm IN X I...

Q:

Q-1 A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted...

Q:

T5 Computational Analysis (Refer the attached sheet). Problem 16. What is economical joint and where does it find applications? A double riveted double cover butt joint is used to connect plates 12...

Q:

Q3/Two plates of 6 mm thick are connected by a triple riveted lap joint of zig-zag pattem. Calculate the rivet diameter, rivet pitch, margin and distance between rows of rivets for the joint. Also,...

Q:

21:19 L3 Statics Assignment 3... 4. Two steel plates are riveted together by means of a single lap joint as shown in Figure 3. Six rivets of diameter 9mm are used, and the load carried is 20kN. What...

Q:

Q3/ Two plates of 6 mm thick are connected by a triple riveted lap joint of zig-zag pattem. Calculate the rivet diameter, rivet pitch, margin and distance between rows of rivets for the joint. Also,...

Q:

please solved this question quickly and percent quickly See table 1 to get the values for P1,P2 in KN, C in mm and e1,e2 in mm. An eccentrically loaded lap riveted joint is to be designed for a steel...

Q:

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Q:

See table 1 to get the values for P1,P2 in KN,C in mm and e1,e2 in mm. An eccentrically loaded lap riveted joint is to be designed for a steel bracket as shown in Fig. 3. The bracket plate is 15 mm...

Q:

For the given mechanical system in Fig. 1. A weight-lifting mechanism. The pulley is used to support the rob which lifts the load. Pulley is linked to a solid rectangular plate using a riveted joint....

Q:

What factors do you think differentiate good decision makers from poor ones? Relate your answer back to the six-step rational decision-making model.

Q:

The balance in the unearned fees account, before adjustment at the end of the year, is $23,676. Journalize the adjusting entry required assuming the amount of unearned fees at the end of the year is...

Q:

Nep Smove 4 Int Svemt Mary Sue owms 1 0 0 0 shares of ORS Moving Company. OES pays a yearly dividend of $ 1 0 0 per share. What is the total annusi dividend that Mary Sue will receive? Matiote Choice...

Q:

If f(x)=2x^(2)-3 and g(x)=x+5, Find: (remember to do exponents first, then ) (multiply, then add or subtract. ) 1. 0 answers