Question: Design a protected C . I flange coupling for a solid shaft for transmitting power of 3 6 . 5 kW at 5 0 0

Design a protected C.I flange coupling for a solid shaft for transmitting power of 36.5 kW at 500 rpm. Materials for the shaft, flanges and key are 30C8,200 F.G C.I and 20C4 steel respectively and bolts are made of 20C4 steels. Assume the value of factor of safety as per the requirement.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Design a shaft and flange for a Diesel engine in which protected type of flange coupling is to be adopted for power transmission. The following data is available for design: Power of engine = 75 kW;...

Q:

Question 0 3 A motor is directly coupled to a gear box by means of a protective flange coupling. Both shafts which connect the motor and gear box are made of steel having allowable stress of \ ( 4 0...

Q:

Design & draw a protective type CI flange coupling for a steel shaft transmitting 15 kW at 200 rpm & having an allowable shear stress of 40 MPa. The working shear stress in the bolts shouldn't exceed...

Q:

3. A shaft transmitting 150 kW is to be connected to a coaxial shaft through cast iron flange coupling. The shaft runs at 120 rpm. The key and shaft are to be made of same material for which...

Q:

Question 1 A 100 mm diameter shaft with a length of 6 m is connected by a flange coupling and transmitting maximum power. A square key of 20 mm is used to connect the shaft and the hub. The coupling...

Q:

Problem Statement: It is required to design a pin bush type flexible flange coupling to connect two shafts. The input shaft transmits 1 0 kW power at 1 8 0 rpm to the output shaft through the...

Q:

9. 10. 11. 12. 13. Determine the torque received by the motor shaft running at 4250 rpm, transmitting 11 HP, through a 10 in diameter, 20 involute gear. The shaft is supported by ball bearings at...

Q:

Design a Cast Iron flange coupling for a mild steel shaft transmitting 9 0 KW at 2 5 0 rpm . The allowable shear stress in the shaft is 4 0 MPa and the angle of twist is not to exceed 1 0 in a length...

Q:

Question 1 A Solid steel shaft running at 6 0 0 rpm is supported on bearings 6 0 0 mm apart. The shaft receives 4 0 kW through a 4 0 0 mm diameter pulley weighing 4 0 0 N located 3 0 0 mm to the...

Q:

Two shafts made of plain carbon steel are connected by a rigid protective type flange coupling. The shafts are running at 500 r.p.m. and transmit 25 kW power. Design the coupling completely for over-...

Q:

A metal sphere 25 mm in diameter was heated to 95°C, and then suspended in air at 22°C. The mass density of the metal is 7920 kg/m3, its specific heat at 30°C is cp = 500 J/(kg.°C),...

Q:

In Problem 14.8 on page 584, you used the land area of a property and the age of a house to predict appraised value (stored in GlenCove). a. Perform a residual analysis on your results. b. If...

Q:

2 a Work out the answer to each calculation. Use the diagrams to help you. b Write the answers to i ii 2+ 3 iv

Q:

la general, when compured with fizus with high business risk, firms with a low degree of business risk, such as electric utilities, are more likely to have a capsal structure with moreOAO B ) equingO...