Question: Determine the binary output code of a 3 - bit flash ADC for the analog input signal shown below, sampled every 1 0 s beginning

Determine the binary output code of a 3-bit flash ADC for the analog input signal shown below, sampled every 10 s beginning at t=20s.
Assume 1 ADC bit =1Vin. Note that the maximum 3-bit digital output code is 1112=710, so any voltage above 7 V will cause the ADC to saturate at its maximum output code.
v
\table[[t,Code],[20s,001],[30s,],[40s,],[50s,],[60s,],[70s,],[80s,],[90s,],[100s,],[110s,],[120s,],[130s,],[140s,],[150s,],[160s,],[170s,],[180s,],[190s,],[200s,]]
Determine the binary output code of a 3 - bit

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

Testbench module you need to use for testing: module adcinterface_tb(); parameter N = 12; // Number of ADC bits (LTC2308 is a 12-bit ADC) logic clk, reset_n; // clock and reset logic [2:0] chan; //...

Q:

Could you write a module for this? I have attached page 10 and 17 from datasheet and testbench module you need to test with if you need these. Thank you. Testbench module: module adcinterface_tb();...

Q:

MulitSim Simulation of A/D and D/A Converters. 1. Simulate a 4-bit R-2R Ladder Digital to Analog Converter. Use two op-amps (opamp_3T_virtual) with pos and neg swing voltages of + 20V. The second...

Q:

***The sampling code is: (THIS IS THE ONE YOU NEED TO MODIFY TO ANSWER THE ABOVE QUESTION) % % ECE3614 Introduction to Communications % % Matlab Assignment 3: Sampling % % This example demonstrates...

Q:

microcontroller 8051 (MPC82G516A) to finish square wave generation. (timer) question fig. microcontroller 8051 (MPC82G516A) to finish square wave generation. some code picture number is 10626140...

Q:

CNIT 105 Assignment10 Due: Wed. 4/11/18 20 Points Objectives: o Number Systems o Bitwise Operations o Masking Program: Write a C program to extract some information from a whole number for a secret...

Q:

For the data communication system shown above, the source encoder (with code efficiency n=0.8) translates every source symbol into a binary source code word and then the channel encoder inserts an...

Q:

Consider a three-bit analogue to digital converter (ADC) (as illustrated below) for the case of a sinusoidal input (as an example). Here any sample is quantised by rounding either up or down. That...

Q:

Integrity Checking Using CRC For this assignment you will write a CRC integrity checking program will have two modes of operation. Your program must implement the CRC calculation method involving...

Q:

************NEED HELP URGENT**************** *************IN C LANGUAGE****************** Integrity Checking Using CRC For this assignment you will write a CRC integrity checking program will have...

Q:

What are the major types of wired and wireless transmission media? What 3-are the strengths, weaknesses, and potential of each?

Q:

You work as an operations consultant for a textile company. Your client has a well-established distribution system in the US market. The company has hundreds of stores and four distribution centers....

Q:

A machine with a cost of $ 1 0 0 , 0 0 0 and accumulated depreciation of $ 9 8 , 0 0 0 is sold for $ 7 0 , 0 0 0 cash. The amount that shmuld be reported as a source of cash under cash flows from...

Q:

9. Halka Company buys on terms of 3/10, net 80 days. It does not take discounts, and it typically pays on time, 80 days after the invoice date. a. What is the nominal annual percentage cost of its...