Question: Determine the maximum force P that the lap joint shown below can safely carry. All plates are 1 2 mm thick in Grade S 2

Determine the maximum force P that the lap joint shown below can safely carry. All plates are 12
mm thick in Grade S235 and the bolts are M16 in Grade 5.6Determine the maximum force P that the lap joint shown below can safely carry. All plates are 12
mm thick in Grade S235 and the bolts are M16 in Grade 5.6.
30mm50mm30mm
Determine the maximum force P that the lap joint

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

A single lap joint consists of 16 mm thick grade S275 plate as shown in Figure Q1. All edges of the plates are machine flame cut. Two (2) 22 mm diameter Grade 4.6 black non- preloaded bolts and shear...

Q:

Figure 6 shows two plates of thickness t = : 6 mm and width (into the paper) 50 mm tha are joined by a bolted lap joint. The joint is loaded by a tensile force P = 7.0 kN. Find the maximum tensile...

Q:

(a) A steel truss is being designed. One of the tension members is 1200 mm long and is to carry an ultimate tension force, N* = 550 kN. Design a pair of back to back Equal Angle tension members of...

Q:

Two 8 mm & one 12 mm thick S275 plates, shown in Figure Q2, are connected by two 20 mm diameter Grade 8.8 black bolts. Assuming the bolt is fully threaded and all edges are either rolled or machine...

Q:

QUESTION-1) The tension element Tu, which consists of one L80x80x5 corner bracket, which is connected to the 15 mm thick flag plate with 2 bolts, is exposed to the axial tensile force. Flag plate and...

Q:

3- Let the density of the pyramid material be p = 2000 kg/m. Determine the average normal stress at a cross section located at x measured from the apex. Express the stress as a function of x. Assume...

Q:

QI/ A/ Two copper plates of 25 mm thick and of 60 kN strength are riveted by a single lap joint. If the allowable shearing and bearing stresses for the rivet are 100 MPa and 170 MPa, respectively,...

Q:

The cross section of a railway bridge deck is shown in Figure 2 . The bridge deck comprises of two steel girders which are 2 m apart. The bridge span is 10 m and the steel girders are simply...

Q:

CASE 16 Nucor Corporation in 2014: Combating Low-Cost Foreign Imports and Depressed Market Demand for Steel Products Arthur A. Thompson The University of Alabama n 2014, Nucor Corporation, with a...

Q:

CASE 16 Nucor Corporation in 2014: Combating Low-Cost Foreign Imports and Depressed Market Demand for Steel Products Arthur A. Thompson The University of Alabama n 2014, Nucor Corporation, with a...

Q:

Next question Introduce slack variables as necessary and then write the initial simplex tableau for the given linear programming problem. Complete the initial simplex tableau. X x2 X3 S 3 5 2 1 7 2 1...

Q:

The research topic is Factors that drive donor support to cultural organizations in kenya. Describe the dependent variable as donor support in form of financial aid and the independent variable as...

Q:

8. Which gas in air is needed for combustion? (a) nitrogen (b) oxygen (c) argon (d) carbon dioxide

Q:

6. Define a change in estimate and provide an illustration. When is a change in accounting estimate effected by a change in accounting principle? A change in an estimate is simply a change in the way...