Question: Determine the proper diameter d for a solid steel shaft to transmit 2 0 0 hp at 1 0 5 rpm if the working stress

Determine the proper diameter d for a solid steel shaft to transmit 200 hp at
105 rpm if the working stress in shear is 420kgcm2. Ans. d=11.8cm.
Determine the proper diameter d for a solid steel

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A solid steel shaft AB, shown in the figure, is to be used to transmit 5 hp from the motor M to which it is attached. If the shaft rotates at v = 175 rpm and the steel has an allowable shear stress...

Q:

uiz 1. 1) A solid steel shaft in a rolling mill transmits 20 kW of power at 2 Hz. Determine the smallest safe diameter of the shaft if the shear stress tw is not to exceed 40 MPa and the angle of...

Q:

9. 10. 11. 12. 13. Determine the torque received by the motor shaft running at 4250 rpm, transmitting 11 HP, through a 10 in diameter, 20 involute gear. The shaft is supported by ball bearings at...

Q:

5 - 5 Repeat Problem 5 - 1 by first plotting the failure loci in the A , B plane to scale; then, for each stress state, plot the load line and by graphical measurement estimate the factors of safety....

Q:

1 . ) A motor supplies 1 7 4 hp at 5 0 0 rpm to flange A of the shaft. Gear B transfers 6 9 hp of power ( so use this power to determine T B ) to operating machinery in the factory, and the remaining...

Q:

A tensile member in a machine structure Torsion Compute the torsional shear stress in a circular shaft with a diameter of 5 0 mm that is subjected to a torque of 8 0 0 N - m . Compute the torsional...

Q:

Question 1 A shaft is used to transmit power using a gear and pulley. The gear has a diameter of 2 5 cm and drives a mating gear with an upward vertical tangential force ( F t = 8 5 0 0 N ) . The...

Q:

2 3 . The shaft in Figure P 1 2 - 2 rotates at 2 0 0 rpm . Pulley \ ( A \ ) receives 1 0 hp from below. Gear \ ( C \ ) delivers 6 hp to the mating gear below it . Chain sprocket \ ( D \ ) delivers 4...

Q:

The shaft in Figure P 1 2 - 2 rotates at 2 0 0 rpm . Pulley A receives 1 0 hp from below. Gear C delivers 6 hp to the mating gear below it . Chain sprocket D delivers 4 hp to a shaft above. Use SAE 1...

Q:

The goal of the project is to perform analysis and design of the complete shaft, including the specification of the overall geometry and the consideration of stress concentration factors. The...

Q:

Review below company's information to compute costs to products using first-in, first-out (FIFO) costing approach. Process Excellence (PE), Inc. has two production departments: Mixing and Packaging....

Q:

Lucas Clinics last dividend (Do) was $1.50. Its current equilibrium stock price is $15.75, and its expected growth rate is a constant 5 percent. If the stockholders required rate of return is 15...

Q:

Required information LO 7 - 1 : Determine the payback period for an investment. Skip to question We will cover what capital budgeting decisions are and the importance of time value of money in...

Q:

Question 1 (1 point) Year Nominal GDP Deflator Real GDP 1980 $12 $24 1990 18 75 2000 80 22.5 base 2010 20 20 GDP in trillions of dollars. Fill in the blanks using onlyintegers. Do not use any...