Question: Determine the required length L for the single lap connection shown. The plates are ASTM A 3 6 steel and the weld is

Determine the required length "L" for the single lap connection shown.
The plates are ASTM A36 steel and the weld is made using an E80 electrode.
The maximum expected applied load " P " is 80 kips
Weld material is to run across the full end of the connected piece as shown.
State your answer to the nearest full inch value.
Determine the required length " L " for the

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

21:19 L3 Statics Assignment 3... 4. Two steel plates are riveted together by means of a single lap joint as shown in Figure 3. Six rivets of diameter 9mm are used, and the load carried is 20kN. What...

Q:

Please answer Analysis # 2 and 4. E.g. If I: = 119.36 s, then 111 3 213363560 = 57.09639050illati0ns. However, since m must be an integer, we take m = 57 since it is the closest integer. 9. Now,...

Q:

Please answer Analysis #2 and #4. Also, please explain why the % difference is not within 0.2% in #2. E.g. If I: = 119.36 s, then 111 3 213363560 = 57.09639050illati0ns. However, since m must be an...

Q:

Please answer Analysis #1 and #6 THE PHYSICAL PENDULUM Object: To determine the acceleration of gravity g, and the radius of gyration of a bar k, together with their estimated random errors. Required...

Q:

Summarize this for me. Someone who understand the HEA and MEA perfectly and also the summary should be 2 or over 2 pages. Someone who understands this perfectly A scrap-tolerant alloying concept...

Q:

I need help with this lab. Please answer questions for pages 4-7. Freefall Purpose: We will measure the value of 'little g', or the acceleration due to gravity on the surface of Earth. The particular...

Q:

DETAILS What is the maximum segment length of a 100Base-FX netdwork, The last character ('X', etc) refers to the line code method used. Line code is a patdtern of voltage, current or photons used to...

Q:

answer all questions promptly What is the maximum segment length of a 100Base-FX netdwork,Thelast character('X', etc) refers to the line code method used. Line code is a pattern of voltage, current...

Q:

PLEASE COMPLETE NO LATER THAN 11/04 @8am Each question(1,2,& 3) must be a minimum of 200 words. Please EXPLAIN answers in FULL detail and make answers knowledgeable based off the attached reading,...

Q:

E-Physics Tutorial Book Note: I have attached below the lesson for the 3 activities. Thank you so much for your time and effort. Activity 1. Directions: Use the right-hand rule to determine the...

Q:

Find general solution for P.D.E. P.D.E. (D +2D D,-5D,D-6DU = 0

Q:

An article about the California lottery that appeared in the San Luis Obispo Tribune (December 15, 1999) gave the following information on the age distribution of adults in California: 35% are...

Q:

1 The end of each month | Any pereliminary cauh balance above 5 7 2 0 0 is uned to mepary loats at monthend. The cavh balance on budgeted cash poyments fother than for ioan or interest...

Q:

You manage a research group and are under pressure to come up with something new and innovative. Sam, one of your bright young engineers, bursts into your office and excitedly tells you that he has...