Question: Example 1 . Design and draw a cotter joint to support a load varying from 3 0 kN in compression to 3 0 kN in

Example 1. Design and draw a cotter joint to support a load varying from 30 kN in compression to 30 kN
in tension. The material used is carbon steel for which the following allowable stresses may be used. The
load is applied statically.
Tensile stress = compressive stress =50MPa; shear stress =35MPa and crushing stress =90MPa.
Example 1 . Design and draw a cotter joint to

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Q.3 a cotter joint to support a load varying Design from 30 kN in compression to 30 kN in tension. The material used is carbon steel for which the be used. The following allowable stresses may load...

Q:

Question 1 A Solid steel shaft running at 6 0 0 rpm is supported on bearings 6 0 0 mm apart. The shaft receives 4 0 kW through a 4 0 0 mm diameter pulley weighing 4 0 0 N located 3 0 0 mm to the...

Q:

A CASE STUDY OF TUNNEL INSTABILITY IN WEAKNESS ZONE CONTAINING SWELLING CLAY Dawei Mao1,2 Bjrn Nilsen Shurong Feng ? Haibin Zhao 2 Ming Lu14 1 Nanyang Technological University, Singapore PowerChina...

Q:

PART A - MATERIAL PROPERTIES IN UNIAXIAL TENSION Objective To demonstrate the behaviour of brittle and ductile materials in uniaxial tension. Introduction to the Tension Test The term tension test is...

Q:

a ) Design a typical cotter joint ( with drawing ) shown below to transmit a load of 5 0 kN in tension or compression. Consider that the rod, socket and cotter are all made of a material with the...

Q:

Instructor: Ameh Fioklou, Ph.D., P.E. 1 of 7 CE 310 Elementary Structural Analysis Final Project Computer Applications Fall 2021 The objective of this project is to get you familiar with structural...

Q:

To use Allowable Stress Design to calculate required dimensions using a specified factor of safety. A structural element that carries a load must be designed so that it can support the load safely....

Q:

I hope you can answer this question and find the reference below the question. Thank you Topic: Conducting personal job interviews using the STAR model 1- Design a two-hour training work plan for 10...

Q:

1 . Which statement is incorrect regarding the method of joints? A . It can be applied to three - dimensional trusses without any modification. B . It involves solving simultaneous equations for each...

Q:

A truss bridge is to be constructed, supported at points A and B. A truss with joint connections, consisting of steel bars screwed together at node plates (truss nodes, see detailed illustration...

Q:

Giving the following data , draw the balance sheet USING EXCEL :$150,000 lands-:$200,000 equipment :$170 0,000 buildings :$140 ,000account receivable :$ 85,000 account payable - :$10,000 retained...

Q:

Determine the reaction at the support A of the propped cantilever beam.

Q:

The ideal correlation for portfolio construction is: 0 . 0 . 1 . 0 . - 1 . 0 . 0 . 2 5 .

Q:

Para pagar un prstamo de $400,000, debe hacer 16 pagos igualescada seis meses. Si la tasa de inters del prstamo es del 6% anualcapitalizable semestralmente, cul es el principal pagado en e 1 answer