Question: For the beam and loading shown, use the moment - area method to determine the reaction at the roller support. Assume that the flexural rigidity

For the beam and loading shown, use the moment-area method to determine the reaction at the roller support. Assume that the
flexural rigidity El of the beam is constant. (Round the final answer to four decimal places.)
The reaction at the roller support is
wLuarr.
For the beam and loading shown, use the moment -

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

A continuous beam as shown in Figure Q1 has fixed support at A and pinned supports at B, C and D. The beam is subjected to a point load of 5 kN at point E, a uniformly distributed load of 6 KN/m...

Q:

I need a solution to this question For the system shown in the figure, determine, by the method of consistent deformations, the reaction at support e. The flexibility of the spring f = 0.2 cm/kN of...

Q:

Structural Theory 76. The slope at any point in the elastic curve is deflection at that same point is maximum. A positive B. negative C. tangent D. zero when the 77. The product of the modulus of...

Q:

For the beam in Figure 1 below, the flexural rigidity of the beam from point 1 to point 2 is EI while from point 2 to 4 is 2EI. (a) Use stiffness coefficient method to calculate and plot dimensioned...

Q:

(a) A beam as shown in Figure 1 is subjected to a point load of P kN at point B and a concentrated moment of M kNm at point E. Flexural rigidity for spans AC and CE are 2EI and EI, respectively....

Q:

QUESTION #4 Trusses 3 m. BY 3 m 5 kN 4 kN 3 m 3 m Figure 3 5 m [21 marks] As shown in Figure 3, a truss is pinned to a vertical wall D and rolls on a horizontal surface at E. (a) Determine the...

Q:

A wooden beam is loaded by a distributed load w = 5 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1600 mm, LBC = 3400 mm, W=190 mm, Bo = 20...

Q:

The beam shown in the figure consists of a W360 x 79 structural steel wide-flange shape [E = 200 GPa; I = 225 106 mm*]. For the loading shown, determine: (a) the reactions at A, B, and C. Enter a...

Q:

3. Using virtual work method, determine the reactions at the supports A and B of the beam shown in Fig. 3, then draw the moment diagram. Assume the support at B is a roller. El is constant.[ Hint:...

Q:

The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a single live load of 40 k and (c) the maximum positive shear at E. Assume A and C are rollers, D is a pin, and...

Q:

Write a MEMO ParlaTech is a technology company that specializes in machine to machine (M2M) communication. They offer solutions that allow a remote set of machines to send data back to a central hub,...

Q:

Nik, Nur and Co. audited the accounts of Top Batik Sdn. Bhd., a textile company. Upon completion of the audit, the auditors issued 15 copies of the audited financial statements. The firm is aware...

Q:

A small manufacturing company is considering expanding its operations by investing in new machinery. The investment requires a significant loan, but the company is uncertain about future market...

Q:

On the date of 1/4, a debit current account was opened for Anoud with a ceiling of 35,000 dinars and a commission of 2% On 4/5, Anoud withdrew from her debit current account an amount of 5,000 dinars...