Question: 1. (10 pts) Water flows through a horizontal bend and discharges into the atmosphere as shown. When the pressure gauge reads 10 psi, the

1. (10 pts) Water flows through a horizontal bend and discharges into

1. (10 pts) Water flows through a horizontal bend and discharges into the atmosphere as shown. When the pressure gauge reads 10 psi, the resultant x-direction anchoring force, FAX, in the horizontal plane required to hold the bend in place is shown in the figure. Determine the flow rate through the bend and the y-direction anchoring force, Fay, required to hold the bend in place. The flow is not frictionless. Ans: 7.01 ft/s and 674 lbs. Q=? Area - 0.2 ft 10 psi Water Area = 0.1 ft 45 Bend F = ? FA 1440 lb

Step by Step Solution

★★★★★

3.48 Rating (145 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Water ( = 1000 kg/m 3 ) flows through a horizontal bend and T section as shown. At section a the flow enters with a velocity of 5 m/s, and the pressure is 4.8 kPa gage. At both sections b and c the...

Water flows through a horizontal tube of diameter 2.5 cm that is joined to a second horizontal tube of diameter 1.2 cm. The pressure difference between the tubes is 7.3 kPa. (a) Which tube has the...

Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate. The force required to hold the plate steady is 70 N. Assuming frictionless one-dimensional flow, estimate (a)...

Tire and automobile manufacturers and consumer safety experts all recommend that drivers maintain proper tire pressure in their cars. Consequently, many gas stations now provide air pumps and air...

Air flows steadily through a horizontal 4-in.-diameter pipe and exits into the atmosphere through a 3-in.-diameter nozzle. The velocity at the nozzle exit is $150 \mathrm{ft} / \mathrm{s}$....

A counter flow, twin-tube heat exchanger is made by brazing two circular nickel tubes, each 40 m long, together as shown below. Hot water flows through the smaller tube of 10-mm diameter and air at...

Information: Trey Monson starts a merchandising business on December 1 and enters into the following three inventory purchases. During December, Monson sells 15 units for $20 each on December 15....

A 2-mm-thick piece of sheet steel is cut and bent into the machine component shown. Knowing that the density of steel is 7850 kg/m3, determine the mass moment of inertia of the component with respect...

A section of sheet steel 3 mm thick is cut and bent into the machine component shown. Knowing that the density of the steel l is 7860 kg/m3, determine the mass products of inertia Ixy, Iyz, and Izx...

A section of sheet steel 0.08 in. thick is cut and bent into the machine component shown. Knowing that the specific weight of steel is 490 lb/ft3, determine the mass products of inertia a Ixy, Iyz,...

Hashira Sdn. Bhd. produces two products that uses the same ingredients but at different levels. The two products, X and Y earns a contribution of RM20 and RM30 per liter respectively. Due to the...

Southern Industries report the following information pertaining to a recent month: Job 1 Job 2 Job 3 Direct Materials $50 $60 $30 Direct Labor 20 30 10 Manufacturing Overhead 40 60 20 By the end of...

D o the following with the given information. 0 1 2 3 c o s ( x 2 ) d x ( a ) Find the approximations T 8 and M 8 for the given integral. ( R o u n d your answer t o six decimal places. ) T 8 = M 8 =...

Q#4: Calculate the Vertical stress at the following depths of 1.5m, 3m, 4.5m, 6m and 12m on the ground surface for the points are (a) r 0. Given R 3m and the increased in stress is 100KN/m2 on the...

Demonstrate how the following objectives relate to a current accounting event in the business environment. Please include your references 1. Manufacturing activities and the flow of manufacturing...

Which of the following are integrated when an organization formulates a strategic plan? (Select all that apply.) Multiple select question. policies past philanthropic gifts action sequences major...

Question 1 10 pts am: When a particle is located a distance 3 meters from the origin, a force of COS (?) newtons acts on it. How much work is done in moving the particle from a: = 1 to a: = 2?...

I'm having trouble answering these questions for math. I don't understand the concepts. Help is greatly appreciated! D Question 7 10 pts Suppose that Juan can choose to get home from work by car or...

Find 1. (10 pts) The posterior distribution of , and via simulation: 2. (10 pts) P(2 > 1 | data) 3. (10 pts) A 95% Central CI for the correlation between yi,1 and yi,2 (i.e. for ()1,2/ p ()1,1(2,2)...

1. (10 pts) Find a, b, and c for the function f(x) = asin(bx + c) such that the graph of f matches the figure. -3+ 2. (20 pts) Find the exact value of the following expression. (a) arccos cos 2" )...

Question 3 10 pts Let us assume that the world price is p_w=200. What can we say about this market? O It is an import competing market, therefore the country has an advantage in this product. O It is...

Question 1 10 pts A child on a merry-go-round takes 5.1 s to go around once. What is his angular displacement during a 2.5 s time interval? Assume uniform circular motion. Question 2 10 pts A...