Question: A simply supported beam with builteup Crass- section, as shown in Figure Find maximum alowable lo ad (w ? kN/m), so that: bending stress

A simply supported beam with builteup Crass- section, as shown in Figure

A simply supported beam with builteup Crass- section, as shown in Figure Find maximum alowable lo ad (w ? kN/m), so that: bending stress not exceed (8MP), flexural shear Stress (6.70 MPa),and shear stress of balts ( Fm) O distances (8o mm c/c) is (56 MPa). 4.5m 3 m 1.5m 50 mm 200 mm 50 Mm 50 300 mm + Ans. 10.06 KN/) AAl.

Step by Step Solution

★★★★★

3.33 Rating (150 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (2 attachments)

63638ac965657_238437.pdf

180 KBs PDF File

63638ac965657_238437.docx

120 KBs Word File

Students Have Also Explored These Related Mathematics Questions!

In 1990 about 50% of Americans considered the low quality of education as a serious problem for the country. What is the chance that sample proportion will reflect the proportion of the total...

A simply supported beam loaded by two forces is shown in the figure. Select a pair of structural steel channels mounted back to back to support the loads in such a way that the deflection at midspan...

A simply supported beam (see figure) is 64 feet long and has a load at the center. The deflection of the beam at its center is 1 inch. The shape of the deflected beam is parabolic. (a) Write an...

A simply supported beam is subjected to distributed loads w1 and w2 as shown. The bending moment as a function of x is given by the following equations: M(x) = RAx W1x2/2 for 0 M(x) = RAx w1a/2 (2x ...

From mechanics of materials it is known that for a simply supported beam of uniform cross section a static load P applied at the center will cause a deflection A = PL3/48EI, where L is the length of...

Consider a simply supported beam of rectangular cross section of constant width b and variable depth h, so proportioned that the maximum stress x at the outer surface due to bending is constant, when...

Consider the simply supported beam with an intermediate load in Appendix A96. Determine the deflection equation if the stiffness of the left and right supports are k1 and k2, respectively.

Consider the simply supported beam with a uniform load in Appendix A97. Determine the deflection equation if the stiffness of the left and right supports are k1 and k2, respectively.

The simply supported beam is subjected to the loading shown. Determine the deflection at its center C. EI is constant. 6 kip/ft 5 kip-ft A 8 ft- 8 ft

A vaulter holds a 29.4-N pole in equilibrium by exerting an upward force U with her leading hand and a downward force D with her trailing hand, as shown in Figure P12.25. Point C is the center of...

Name at least three daily sanitation-related concerns that you would have if you were the general manager of a limited-service hotel offering a complimentary breakfast bar.

1. For its first year of operations, Tringali Corporation's reconciliation of pretax accounting income to taxable income is as follows: Pretax accounting income $220,000 Permanent difference (14,000)...

28. Discounted Cash Flow Analysis (LO1) If the appropriate discount rate for the following cash flows is 9 percent compounded quarterly, what is the present value of the cash flows? 2 3 123 Year 1...

Marie Stefano is the group director of customer training for Mayfield Software. In this capacity, she runs a center in Kirkland, Washington, that provides training to employees of companies that use...

Shynee Minerals processes materials extracted from mines. The most common raw material that it processes results in three joint products: Sarco, Barco, and Larco. Each of these products can be sold...

Mills Company lists the following condensed balance sheet as of the beginning of 2007: Mills is considering the impact of various types of dividends on this balance sheet. Each dividend would be...

Reread the Management Focus box on Procter & Gamble and then answer the following questions: a. What strategy was Procter & Gamble pursuing when it first entered foreign markets in the period up...

A city established a public housing authority to fund the construction of low-income residential homes within city limits. The authority is governed by a nine-person board of trustees. New trustees...

What is the net force and acceleration of a ball of mass 0.750 kilograms that is subjected to forces of 11.00 newtons and 7.00 newtons from opposite directions

Programming project Choose from the following themes/topics: 1- Plane stress transformation 2. Plane strain transformation 3. Strain rosettes (arbitrary directions) 4- 60-degree rosettes 5- 45-degree...

( a ) A 5 - metre - long uniform beam is simply supported at both ends and is subjected to the uniformly distributed load shown in the Figure 1 . Figure 1 : A simply supported beam subjected to a...

6. A simply supported beam with length L has a point load with magnitude, P, in the center (Figure 3a). A second simply supported beam with length 2L (with the same cross sectional geometry as the...

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....