I need help!

Part 1:Develop the IPv4 Addressing Scheme

Total points: 20

Time: 25 minutes

Given an IP address and mask of ____192.168.218.0____________ (address / mask), design an IP addressing scheme that satisfies the following requirements. Network address/mask and the number of hosts for Subnets A and B will be provided by your instructor.

Subnet	Number of Hosts
Subnet A
Subnet B

The 0^th subnet is used. No subnet calculators may be used. All work must be shown on the other side of this page.

Subnet A
Specification		Student Input	Points
Number of bits in the subnet			(7 points)
IP mask (binary)
New IP mask (decimal)
Maximum number of usable subnets (including the 0th subnet)
Number of usable hosts per subnet
IP Subnet
First IP Host address
Last IP Host address

Subnet B
Specification		Student Input	Points
Number of bits in the subnet			(7 points)
IP mask (binary)
New IP mask (decimal)
Maximum number of usable subnets (including the 0th subnet)
Number of usable hosts per subnet
IP Subnet
First IP Host address
Last IP Host address

Host computers will use the first IP address in the subnet. The network router will use the LAST network host address. The switch will use the second to the last network host address.

Write down the IP address information for each device:

Device	IP address	Subnet Mask	Gateway	Points
PC-A				(6 points)
R1-G0/0			N/A
R1-G0/1			N/A
S1			N/A
PC-B

Points: _________ of 15

Part 2:Initialize and Reload Devices

Total points: 10

Time: 10 minutes

Step 1:Initialize and reload router and switch. (10 points)

Erase the startup configurations and VLANs from the router and switch and reload the devices.

Before proceeding, have your instructor verify device initializations.

Task	IOS Command	Points
Erase the startup-config file on the Router.		(2 point)
Reload the Router.		(2 point)
Erase the startup-config file on the Switch.		(2 point)
Delete the vlan.dat file on the Switch		(2 point)
Reload the Switch.		(2 point)

Points: __________ of 10

Part 3:Configure Device IPv4 and Security Settings

Total points: 35

Time: 25 minutes

Step 1:Configure host computers.

After configuring each host computer, record the host network settings with the ipconfig /all command.

PC-A Network Configuration		Points
Description		(3 points)
Physical Address
IP Address
Subnet Mask
Default Gateway

PC-B Network Configuration		Points
Description		(3 points)
Physical Address
IP Address
Subnet Mask
Default Gateway

Step 2:Configure R1.

Configuration tasks for R1 include the following:

Task	Specification	Points
Disable DNS lookup		(1 point)
Router name	R1	(1 point)
Domain name	ccna-lab.com	(1 point)
Encrypted privileged exec password	ciscoenpass	(1 point)
Console access password	ciscoconpass	(1 point)
Telnet access password	ciscovtypass	(1 point)
Set the minimum length for passwords	10 characters	(2 points)
Create an administrative user in the local database	Username: admin Password: admin1pass	(2 points)
Set login on VTY lines to use local database		(1 point)
Set VTY lines to accept ssh and telnet connections only		(2 points)
Encrypt the clear text passwords		(1 point)
MOTD Banner		(1 point)
Interface G0/0	Set the description Set the Layer 3 IPv4 address Activate Interface	(3 points)
Interface G0/1	Set the description Set the Layer 3 IPv4 address Activate Interface	(3 points)
Generate a RSA crypto key	1024 bits modulus	(2 points)

Step 3:Configure S1.

Configuration tasks for R1 include the following:

Task	Specification	Points
Switch name	S1	(1 point)
Configure Management Interface (SVI)	Set the Layer 3 IPv4 address	(2 points)
Encrypted privileged exec password	ciscoenpass	(1 point)
Console access password	ciscoconpass	(1 point)
Telnet access password	ciscovtypass	(1 point)

Instructor Sign-off Part 3: ______________________

Points: _________ of 35

Part 4:Test and Verify IPv4 End-to-End Connectivity

Total points: 8

Time: 10 minutes

Step 1:Verify network connectivity.

Use the ping command to test connectivity between all network devices.

Note: If pings to host computers fail, temporarily disable the computer firewall and retest. To disable a Windows 7 firewall, select Start > Control Panel > System and Security > Windows Firewall > Turn Windows Firewall on or off, select Turn off Windows Firewall, and click OK.

Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails:

From	To	IP Address	Ping Results	Points
PC-A	R1, G0/0			(1 point)
PC-A	R1, G0/1			(1 point)
PC-A	S1 VLAN 1			(1 point)
PC-A	PC-B			(1 point)
PC-B	R1, G0/1			(1 point)
PC-B	R1, G0/0			(1 point)
PC-B	S1 VLAN 1			(1 point)

In addition to the ping command, what other command is useful in displaying network delay and breaks in the path to the destination? (1 point)

_______________________________________________________________________________________

Points: _________ of 8

Part 5:Configure IPv6 Addressing on R1

Total points: 10

Time: 10 minutes

Given an IPv6 network address of 2001:DB8:ACAD::/64, configure IPv6 addresses for the Gigabit interfaces on R1. Use FE80::1 as the link-local address on both interfaces.

Step 1:Configure R1.

Configuration tasks for R1 include the following:

Task	Specification	Points
Configure G0/0 to use the first address in subnet A.	Assign the IPv6 unicast address Assign the IPv6 link-local address	(4 points)
Configure G0/1 to use the first address in subnet B.	Assign the IPv6 unicast address Assign the IPv6 link-local address	(4 points)
Enable IPv6 unicast routing.		(2 points)

Instructor Sign-off Part 5: ______________________

Points: _________ of 10

Part 6:Test and Verify IPv6 End-to-End Connectivity

Total points: 7

Time: 10 minutes.

Step 1:Obtain the IPv6 address assigned to host PCs.

PC-A IPv6 Network Configuration		Points
Description		(1 point)
Physical Address
IPv6 Address
Default Gateway

PC-B IPv6 Network Configuration		Points
Description		(1 point)
Physical Address
IPv6 Address
IPv6 Default Gateway

Step 2:Use the ping command to verify network connectivity.

IPv6 network connectivity can be verified with the ping command. Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails:

From	To	IP Address	Ping Results	Points
PC-A	R1, G0/0			(1 point)
PC-A	R1, G0/1			(1 point)
PC-A	PC-B			(1 point)
PC-B	R1, G0/1			(1 point)
PC-B	R1, G0/0			(1 point)

Instructor Sign-off Part 6: ______________________

Points: _________ of 7

Part 7:Use the IOS CLI to Gather Device Information

Total points: 10

Time: 10 minutes

Step 1:Issue the appropriate command to discover the following information:

Description	Student Input	Points
Router Model		(2 points)
IOS Image File
Total RAM
Total Flash Memory
Configuration Register
CLI Command Used

Step 2:Enter the appropriate CLI command needed to display the following on R1:

Command Description	Student Input (command)	Points
Display a summary of important information about the interfaces on R1.		(1 point)
Display the IPv4 routing table.		(1 point)
Display the Layer 2 to Layer 3 mapping of addresses on R1.		(1 point)
Display detailed IPv4 information about interface G0/0 on R1.		(1 point)
Display the IPv6 routing table.		(1 point)
Display a summary of IPv6 interface addresses and status.		(1 point)
Display information about the devices connected to R1. Information should include Device ID, Local Interface, Hold time, Capability, Platform, and Port ID.		(1 point)
Save the current configuration so it will be used the next time the router is started.		(1 point)