Question: A diesel engine has a cylinder bore of 100 mm and a maximum gas pressure of 6 Mpa the difference in temperature between the

A diesel engine has a cylinder bore of 100 mm and a

A diesel engine has a cylinder bore of 100 mm and a maximum gas pressure of 6 Mpa the difference in temperature between the inner and outer surface of the cylinder liner is 30 C. If the liner is made of cast iron with an allowance stress of 60 Mpa, determine the wall thickness of the cylinder liner.

Step by Step Solution

★★★★★

3.44 Rating (147 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Thickness t PmaxD 2c C Where P is the max pressu... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A diesel engine has air before compression at 280 K, 85 kPa. The highest temperature is 2200 K and the highest pressure is 6 MPa. Find the volumetric compression ratio and the mean effective pressure...

The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the three torques, plot the shear stress distribution along a radial line for the cross section within...

The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the three torques, determine the absolute maximum shear stress in the shaft. The smooth bearings A and...

Exhaust gas from a diesel engine has 6.5% CO 2 , 4.5% CO, 9.0 O 2 , and the balance N 2 . Estimate the cetane number of the fuel supplied (to the nearest whole number). Component Chemical Formula...

Repeat Prob. 965E if the compression ratio were reduced to 12. Data From Q#65: An air-standard dual cycle has a compression ratio of 20 and a cutoff ratio of 1.3. The pressure ratio during the...

The 5-kg collar has a velocity of 5 m/s to the right when it is at A. It then travels down along the smooth guide. Determine the speed of the collar when it reaches point B, which is located just...

High-power lasers in factories are used to cut through cloth and metal (Fig. P34.23). One such laser has a beam diameter of 1.00 mm and generates an electric field having amplitude of 0.700 MV/m at...

A 5.80-F, parallel-plate, air capacitor has a plate separation of 5.00 mm and is charged to a potential difference of 400 V. Calculate the energy density in the region between the plates, in units of...

A venturi meter similar to the one in Fig. 15.2 has an inlet diameter of 100 mm and a throat diameter of 50 mm. While it is carrying water at 80°C, a pressure difference of 55 kPa is observed...

The diameter of a piston of the steam engine is 300 mm and the maximum steam pressure is 0.7 N/mm2. If the maximum permissible compressive stress for the piston rod material is 40 N/mm2, find the...

The practice by which studios controlled all aspects of the movie business: production, distribution, and exhibition. The practice by which studios controlled all aspects of the movie business:...

Differentiate tan(7x+9x-2.5)

Explain the sources of recruitment.

Differentiate sin(5x+2)

Compute the derivative f(x)=1/ax+bx

What is the meaning of strategic management and what are their objectives and advantages of strategic management?

Interdepartment Services: Step Method O'Brian's Department Stores allocates the costs of the Personnel and Payroll departments to three retail sales departments, Housewares, Clothing, and Furniture....

Per Bag Direct materials: 25 pounds of CWhiz-2000 @ $0.08/lb. = $ 2.00 Direct labor: 0.05 hour @ $32.00/hr. = $ 1.60 The company manufactured 100,000 bags of Cheese-Be-Good in December and used...

While being installed, the 25-kg chute ABCD is attached to a wall with brackets and E and F and is braced with props GH and IJ at its outer edge. Assuming that the weight of the chute is uniformly...

Determine the force in member GH and in each of the members located to the right of member GH for the roof truss shown. State whether each member is in tension or compression. 1,5 AN LAAN

(a) Determine the magnitude and the location of the maximum bending moment in the rod of Prob. 16.73. (b) Show that the answer to part a is independent of the mass of the rod. 1. B In

13. What symptoms occur after damage limited to area MT? What may occur if MT is intact but area V1 is damaged?

12. Why is it useful to suppress activity in the visual cortex during saccadic eye movements?

11. What is prosopagnosia and what does its existence tell us about separate shape recognition systems in the visual cortex?