Question: Q2: A rigid beam AC carries a load (P) and is supported by a pin at C and a tie-rod BD. oallow for the

Q2: A rigid beam AC carries a load (P) and is supported

Q2: A rigid beam AC carries a load (P) and is supported by a pin at C and a tie-rod BD. oallow for the tie-rod BD is 145 MPa, (a) Find the maximum load P that can be supported if the tie- rod has a cross-section of 25mm x 25mm. (b) Find the diameter of a tie-rod required to support 85 kN. (30 Marks)

Step by Step Solution

★★★★★

3.37 Rating (138 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

SO... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (2 attachments)

635f9e2ef2768_232761.pdf

180 KBs PDF File

635f9e2ef2768_232761.docx

120 KBs Word File

Students Have Also Explored These Related Civil Engineering Questions!

QI: Determine the largest weight W which can be supported by the two wires shown in Figure below. The stresses in wires AB and AC are not to exceed 80 MPa and 120 MPa, respectively. The cross-...

In this assignment you need to write a program in MIPS assembly language. Your program should perform following tasks: It should prompt the user to enter five numbers one by one. Once user has...

XYZ Company prepared the following table showing a budget analysis of budget vs. actual expenses for the month of June. The initial budgeted values assumed 10,000 units of production. Management is...

A beam of laser light of wavelength 632.8 nm has a circular cross section 2.00 mm in diameter. A rectangular aperture is to be placed in the center of the beam so that, when the light falls...

A simple beam of rectangular cross section (width 4 in., height 10 in.) carries a uniform load of 1200 lb/ft on a span of 12 ft (see figure). Find the principal stresses (1 and (2 and the maximum...

The deformation in rod AB is ____mm The rigid beam AC is supported by rods AB and CD. The rods are 1.75m long with E = 70 GPa. The cross-sectional area for rods AB and CD are 9 mm2 and 15 mm2,...

The strain in rod CD is _____mm The rigid beam AC is supported by rods AB and CD. The rods are 1.75m long with E = 70 GPa. The cross-sectional area for rods AB and CD are 9 mm2 and 15 mm2,...

A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 1 kN. The material is AISI 1045 hot-rolled steel. If the...

An electrical conductor designed to carry large currents has a circular cross section 2.50 mm in diameter and is 14.0 m long. The resistance between its ends is 0.104 n. (a) What is the resistivity...

A wheel on a freight car carries a load W. If the axle of the car has a diameter D, determine the horizontal force P that must be applied to the axle to rotate the wheel. The coefficient of kinetic...

anyone help this assignment please, in java ThreeCushion please this is simpletest . Overview The purpose of this assignment is to give you lots of practice working with conditional logic and mana...

Hansell Company's management wants to prepare budgets for one of its products, Duraflex, for July 2019. The firm sells the product for $84 per unit and has the following expected sales (in units) for...

The vision statement describes the destination or the future state, but it is the _____ that describes the journey you take to get there. Select an answer: Kirkpatrick model McKinsey 7S model Target...

There are two masses with mass, 2M and M. Which of the following statements is true? Group of answer choices The center of mass is closer to "2m" mass than "m" mass The center of mass is exactly...

Laurie needs to set up her operations to produce an order of 2,000 frozen pies for Thanksgiving. Considering the time to setup her process, she will have 10 working days to make the pies. She plans...

On January 1, 2022, Paxon Corporation acquired all of the outstanding common stock of Saxon Company for $2 billion cash. The prior to the combination, are shown below: Balance Sheets (in millions)...

Coronado Company's inventory records show the following data: Units Unit Cost Inventory: January 1 10300 $9.40 Purchases: June 18 9100 7.00 November 8 6500 8.00 A physical inventory on December 31...

Using (1) or (2), find L(f) if f(t) if equals: t cos 4t

The velocity of a particle is v = v0 [1 sin (t/T)]. Knowing that the particle starts from the origin with an initial velocity v0, determine (a) Its position and its acceleration at t = 3T, (b) Its...

A sign is suspended from two chains AE and BF. Knowing that the tension in BF is 200 N, determine (a) The moment about A of the force exerted by the chain at B, (b) The magnitude and sense of the...

Solve Prob. 6.64 when P = 6 kN. Problem 6.64: The diagonal members in the center panel of the truss shown are very slender and can act only in tension; such members are known as counters. Determine...

Dart Corporation (a calendar year C corporation) would like to invest some of its excess earnings from retail operations in real estate. Dart is considering a purchase of 10 acres of land in a city...

Lisa holds nonrefundable Federal income tax credits of $65,000. Her regular income tax liability before credits is $190,000, and her tentative minimum tax is $150,000. a. What is the amount of Lisa's...

Kiki, who incurred intangible drilling costs (IDC) of $94,000 during the year, deducted that amount. Her net oil and gas income for the year was $110,000. Compute Kiki's AMT preference for IDC.