Question: If the spacing between the beams is 3 m , and assuming the slab design load is 8 kN Im ' , find the min

If the spacing between the beams is 3m, and assuming the slab design load is 8 kN Im', find the min slab thickness. (1.5 hours fire, no probs at the middle )

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

If the spacing between the bearns is 3 m , and assuming the slab design load is 8 k N m 2 , find the min slab thickness ( 1 . 5 hours fire, no probs at the middle )

Q:

3. A multistory cast-in-place reinforced concrete building is to be constructed using a system of shores and reshores. The typical slab thickness is 6". Slab design loads, construction loads, and...

Q:

Just design I beam based on the coding below. R-Studio language. I'm waiting for answer please i don't have much time. Thank You. #------------------------------------ sub function...

Q:

HW # 8 Concrete Slab Formwork Module 2 0 Due Date: 1 1 : 5 9 PM EST on the date given in on Canvas Schedule Refer to the course schedule to find the exact date. Point Value: Max. 5 0 points This...

Q:

A two-way slab floor system as shown below. Concrete strength fc =25MPa and steel yield strength is fy=420MPa. Service live load is 2.0 kN/m and additional dead load is 4.0 kN/m. Story height is...

Q:

Uniformly distributed load: DL + LL load from a rooftop assembly space + dead load ) as wett Answer the following questions. Annotate Figure # 1 in worksheet where noted, otherwise show answers in...

Q:

A small reinforced concrete two storey building ( designed for future construction of another storey above ) has the load bearing layout of the following Figure 2 . You have to design certain...

Q:

Q 2 ) ( 6 0 marks ) For the shown slab supported on beams 1 and 2 , f y = 2 8 0 MPa, f c ' = 3 0 MPa a ) Find the minimum thickness of slab according to ACI ? b ) Find dead load of the slab? Use 3 c...

Q:

A 15m single span post-tensioned rectangular concrete beam is 400mm wide by 1000mm deep, with two cables running side by side, shown in Figure Q3. Each cable is formed by 5 strands, the cable...

Q:

Determine the demand capacity ratio (DCR = Mu / Mn) for a W21x44 (Fy = 50 ksi) with a simple span of 40 ft. The spacing to adjacent beams is 12 ft on each side of the W21x44. The slab is composed of...

Q:

Porter Companys most recent contribution format income statement is shown below: Required: Prepare a new contribution format income statement under each of the following conditions (consider each...

Q:

A survey asked 50 baseball fans to report the number of games they attended last year. The results are listed here. Use an appropriate graphical technique to present these data and describe what you...

Q:

If a registered representative is involved in a trade or collects a commission that did not go through his broker - dealer, he is:

Q:

Complete the truth table for the proposition: -(r +9) (p -r) 1 1 - 79 pA - (r +9) V(pA-r) T T T T T F T F T F T F T F F F

Q:

2. It would cost the town of Irondale $50 million to build a gas- powered generator that could produce a maximum of 5 megawatts of electricity at 15 cents per hour. Another alternative would be for...

Q:

LO20.2 Identify the main categories of government spending and the main sources of government revenue.

Q:

LO20.3 List the main categories of federal revenue and spending and describe the difference between marginal and average tax rates.