In an orthogonal cutting test the following conditions were noted: width chip(width of cut) = 2.5mm unreformed

Fantastic news! We've Found the answer you've been seeking!

Question:

In an orthogonal cutting test the following conditions were noted:

width chip(width of cut) = 2.5mm

unreformed chip thickness = 0.25mm

chip thickness = 1 mm

working normal rake = -5 degrees

cutting force = 900N

thrust force = 900N

Find:

A) The shear angle

B) The mean shear strength of the work material

Related Book For answer-question

Materials and process in manufacturing

ISBN: 978-0471656531

9th edition

Authors: E. Paul DeGarmo, J T. Black, Ronald A. Kohser

See More Books

Posted Date: Oct 25, 2020 04:52 PM

See More Questions

An angle bracket having thickness t= 25 mm is attached to the flange of a column by two bolts of diameter d=20 %3D mm diameter (see figure). A uniformly distributed load from a floor joist acts on...
A square silicone chip 7 mm by 7 mm in size and 0.5 mm thick is mounted on a plastic substrate with its front surface cooled by a synthetic liquid flowing over it. Electronic circuits in the back of...
A flat bar of width b = 60 mm and thickness t = 10 mm is loaded in tension by a force P (see figure). The bar is attached to a support by a pin of diameter d that passes through a hole of the same...
In 2014, Elbert Corporation had net cash provided by operating activities of $531,000; net cash used by investing activities of $963,000; and net cash provided by financing activities of $585,000. At...
1. Is social media a passing fad, or a valuable new way of managing communication? Why? 2. Do you agree that investments in social media are more likely to provide a higher return on investment than...
Under the revaluation model for property, plant, and equipment and the fair model for investment property: A . fair value of the asset must be able to be measured reliably. B . net income is aff...
The 304 stainless steel post A is surrounded by a red brass C83400 tube B. If a force of 5 kip is applied to the rigid cap, determine the required diameter d of the steel post so that the load is...
Suppose you and most other investors expect the inflation rate to be 7 percent next year, to fall to 5 percent during the following year, and then to remain at a rate of 3 percent thereafter. Assume...
On a level football field, a football is projected from ground level. It has speed 12.0 m/s when it is at its maximum height. It travels a horizontal distance of 75.0 m. Neglect air resistance. What...
Two charges +q and 3q are separated by a small distance. Draw the electric field lines for this system.
In what circumstance individuals and companies are treated as a resident of Australia for tax purposes? Discuss based on the provisions of the Income Tax Assessment Act 1936 (Cth) and relevant common...
Michaels Car Repair Services was established on 1 st of July 2020 as a sole proprietor business, specialising in providing car repairs and general maintenance services. The owner, Michael Robert,...
The finance manager of a fastfood restaurant is presented with an opportunity for opening a new location. The company has recently paid a consultant $50,000 for a demographic study about this new...
A monopolistically competitive sneaker firm is currently in long run equilibrium. Graph the firm in long run equilibrium. Be sure to label all of the curves and the profit-maximizing price and...
4. Say that R is a preference relation defined on X and that R is complete and transitive. Show that for all x, y X, if Py, then for any EX, either Pz or Py or both.
By using the definition of Laplace transform, determine {f(t)) if 153 f(t)-2 35155 12.5. . Find the inverse Laplace transform of the following function :- F(s)=- = (5-7) +5 (5 Marks/ Markah) (5...
Calculate the net profit ratio margin for 2019? Required information [The following information applies to the questions displayed below.] Massa Company, which has been operating for three...
The following processes constitute the air-standard Diesel cycle: 12: isentropic compression,23: constant-volume energy addition (T and P increase),34: constant-pressure energy addition (v...
Describe the primary differences between barrel finishing and vibratory finishing.
How does thread milling differ from thread turning?
How are letters incorporated into the AISI-SAE designation system for steel, and what do some of the more common ones mean?
Find out all such terms (synonyms), which mean exactly the same as temptation and can they be used interchangeably?
Create two scenarios other than those given in this chapter, where the temptation pattern can be used.
List some design and implementation issues faced, when implementing the temptation pattern. Explain each issue.

In an orthogonal cutting test the following conditions were noted: width chip(width of cut) = 2.5mm unreformed

Question:

Expert Answer:

Materials and process in manufacturing

Students also viewed these mechanical engineering questions