Question: In Orthogonal Cutting, if the feed is 1.25 mm/rel and Chip thickness after Cutting is 2mm, Determines the following!! Chip thickness ratio, @ Shear

In Orthogonal Cutting, if the feed is 1.25 mm/rel and Chip thickness

In Orthogonal Cutting, if the feed is 1.25 mm/rel and Chip thickness after Cutting is 2mm, Determines the following!! Chip thickness ratio, @ Shear Angle - Given, rank angle = 10; if Shear Strength = 600 N/mm, width of Out - 10mm, Cuffing-speed = 30m/min, Cutting Speed - Bonn/-frien, coefficient of friction =0.9, Determine, (a) Shear force, (b) friction angle, (C) Cutting force ; (d) Horse power. at the Cutting tool.

Step by Step Solution

★★★★★

3.45 Rating (145 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The detailed ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

The cutting tool on the lathe exerts a force F on the shaft in the direction shown. Determine the moment of this force about the y axis of the shaft. Units Used: kN = 103 N Given: F = (6 -4 -7)kN a =...

In Figure 22-A are data for cutting speed and tool life. Determine the constants for the Taylor tool life equation for these data. What do you think the tool material might have been?

A flat bar of width b = 60 mm and thickness t = 10 mm is loaded in tension by a force P (see figure). The bar is attached to a support by a pin of diameter d that passes through a hole of the same...

Consider the straight turning operation of a AISI 1 0 1 0 steel bar with a tool with a rake angle of 5 and a clearance angle of 3 , using the following operating parameters: cutting speed is 3 1 5 m...

In the orthogonal turning of a 6 0 mm diameter mild steel bar on a lathe, the following data were obtained: Rake angle = 1 8 \ deg , cutting speed = 1 2 0 ( m ) / ( m ) in , feed = 0 . 2 5 m ( m ) /...

EXAMPLE In an orthogonal cutting operation on a lathe following observations were obtained. Cutting force F c = 1 2 0 N , Feed Force = F t = 3 0 N , Feed rate = 0 . 2 m m r e v , Cut chip thickness t...

Question 2 : In orthogonal turning of a 5 0 mm diameter mild steel bar on a lathe, the following data were obtained: Rake angle = 1 5 , cutting speed = 1 0 0 m m i n , feed = 0 . 2 m m r e v ,...

Q . 7 Orthogonal cutting was performed with rake angle of 1 2 0 on steel workpiece having specific energy of 2 k N m m 2 using emulsion cutting fluid at 6 litre / min flow rate. The cutting...

Orthogonal cutting was performed with rake angle of 1 2 0 on steel workpiece having specific energy of 2 kN / mm 2 using emulsion cutting fluid at 6 litre / min flow rate. The cutting parameters used...

In an orthogonal cutting operation, following observations were made: i ) Cutting speed = 2 0 m / min , ii ) Width of the cut = 2 . 5 mm , iii ) Feed = 0 . 2 4 mm / rev , iv ) Chip thickness = 0 . 4...

Define and elaborate on the concept of "Cost-Volume-Profit (CVP) Analysis" in managerial accounting. Discuss the various assumptions underlying CVP analysis and their significance in decision-making...

Simply put, it gave the impression that things were three times larger than they actually were. He improved the design of the telescope so that it could zoom in eight times and then thirty. The...

Makeup product (e.g. any one item such as eyeshadows, foundation etc. ) Hint: How will you obtain feedback about competitors' similar products? Use survey or other method for collecting customer...

During July, the following are given: Standard unit price 12.50 Standard Quantity Allowed for actual production 6,300 units Actual unit purchase price Quantity purchased and used for production...

An RFP is used for what type of procurement? Give an advantage and a disadvantage of the RFP process

You are the area manager of several starbucks and you make all of the decisions regarding land, building, and equipment. Additionally you are responsible for all of the profits of the starbucks in...

Advertisers may use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ to mimic word - of - mouth effects of reference group members that consumers identify with. Comparable endorsers Celebrity endorsers Expert...

What is the expected payoff of an investment that yields $5,000 with a probability of 0.15 and $500 with a probability of 0.85? Select one: O a. $325 O b. $5,500 O c. $2,750 O d. $1,175

What tolerances are added to gages when they are being designed?

For orthogonal machining, the cutting edge radius is assumed to be small compared to the uncut chip thickness. Why?

Why is CBN better for machining steel than diamond?

Here are the summary statistics for the weekly payroll of a small company: lowest salary = $300, mean salary = $700, median = $500, range = $1200, IQR = $600, first quartile = $350, standard...

Here is a timeplot of each monthly load factor for domestic flights for 2000 to 2013 along with a lowess smooth. a) Describe the patterns you see in this plot. b) Do you expect the overall pattern to...

The table lists the amount of rainfall (in acre-feet) from the 26 clouds seeded with silver iodide discussed in Exercise 40: a) Why is acre-feet a good way to measure the amount of precipitation...