Question: It is a simulation of a temperature sensor . The input is temperature and the output is voltage value in mV . Entered input values

It is a simulation of a temperature sensor. The input is temperature and the output is voltage value in mV. Entered input values are the real temperature values in terms of C and the corresponding output is the sensors voltage output with possible errors. The sensor is a linear sensor. For the sensor, answer the below question, since there is error, you should make many measurements even for the same real temperature value. (Do not forget the units for your answers)(33p)1- Find Input range. 2- Find Input span. 3- Find output range. 4- Find output span. 5- Find the output sensitivity.6- Find the voltage offset. 7- Find the output error range in your measurement. 8- Find the input resolution. 9- What is the mean of the error in measurements? 10- What is the standard deviation of error in the measurements? 11- Define a formula for the input and output relation for the sensor

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

34. An accelerometer is measuring a structure as described below: Highest frequency measured, f = 300 hz Seismic mass, m = 0.0045 kg Accelerometer spring coefficient, k = 120,000 N/m Accelerometer...

Q:

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

Q:

Where can I get these rough values from, appendix pages are below (a) From the information in the LM301 data sheets provided in appendix B (you can download from Moodle), estimate Ao, o and GBP for...

Q:

PRE-LAB Assignment: I - Setting up Simscape 1. Open MATLAB, open Simulink, and navigate to Simscape (Under the normal Simulink models) 2. Open the template for Three-Phase power systems (Electrical...

Q:

Appendix G: (Not required information but I put it here incase it might help) b. Build a Simulink program based on the transfer function in Eq. (2-8) with R= 10k12 and C = 10uF. to conduct...

Q:

Description : - Simulate the example shown above in Proteus and visualize the results. Describe the limitations of LM35 in Proteus for visualisation of the result. - Increase the resolution of your...

Q:

Use MATLAB for writing code Matlab (or any other simulation software) can be used to develop and test an algorithm, which can later be implemented in a real hardware prototype. The algorithm...

Q:

EET 412 2017-1 1. The number of different possible binary PCM values that can be encoded with 5-bit words is (a) 16 (b) 5 (c) 64 (d) 32 2. An analog signal is to be encoded with at least 2000 values....

Q:

LABORATORY EXPERIMENT NO. 3 ESTIMATION OF EXPERIMENTAL ERRORS THEORY AND MONTE CARLO ANALYSIS I. OBJECTIVES The estimation of experimental errors due to component value variation is explored...

Q:

D O NO T Ta KE IF YOU CANNOT ANSWEAR ALL THE QUESTION AS SUPPOSED OR I WILL RATE UNHELPFUL AND REPORT FOR PLAG Peru Domestic: a bond is issued in the US Global: a bond is issued in the US and foreign...

Q:

What is the effect of multinational operations on capital budgeting decisions.

Q:

Calculate the missing value. Initial value Final value Percent change 0.043 30

Q:

Which statement is correct? In total dollars, cash dividends outweighed stock repurchases for the period 2 0 0 3 - 2 0 1 3 . A non - dividend - paying firm is more apt to do a stock repurchase than...

Q:

Project A requires an initial outlay of $6000 and it willgenerate $6000, $1000, $1000, and $1000 for the next 4 years.Project B requires an initial outlay of $6000 and it will generate$1000, $1000, 2...