Question: lets consider a spherical pressure vessel with an inner radius of 6 0 cm and a wall thickness of 3 mm . if its made

lets consider a spherical pressure vessel with an inner radius of 60 cm and a wall thickness of 3 mm . if its made of a material having the maximum tensile stress of 500 Mpa , the maximum allowable internal pressure will be ?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A cylindrical pressure vessel with an inner radius of 0 . 4 meters and a wall thickness of 1 2 mm is subjected to an internal pressure of 5 MPa. Determine the hoop stress and longitudinal stress in...

Q:

A cylindrical pressure vessel with an inner radius of 0 . 4 meters and a wall thickness of 1 2 mm is subjected to an internal pressure of 5 MPa. Determine the hoop stress and longitudinal stress in...

Q:

The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 18 mm. It is made from steel plates that are welded along the 45 seam. Part A Determine the normal stress...

Q:

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A hollow cylindrical shaft with an outer diameter of 8 0 mm and an inner diameter of 6 0 mm is subjected to a bending moment of 9 0 0 Nm and a torque of 7 0 0 Nm . Calculate the maximum principal...

Q:

2.2 A small closed cylinder has dimensions 50 mm external diameter by 160 mm long with 0.25 mm wall thickness. (a) What is the allowable internal pressure if the safe tensile stress for the material...

Q:

A2. Pressure vessels Consider the two pressure vessel geometries shown below. Both are thin-walled vessels made of titanium 6A1-4V; both are to be pressurized from 0 to the same pressure, p: and both...

Q:

Consider the two pressure vessel geometries shown below. Both are thin-walled vessels made of titanium 6Al-4V; both are to be pressurized from 0 to the same pressure, p; and both have the same...

Q:

As production manager, Mr. B is asked to track the manufacturing cost per unit on the factory floor. Total manufacturing costs were $97899 before considering factory maintenance salaries of $12,000...

Q:

Using the Tax Rate Schedules. The IRS publishes Tax Rate Schedules and a Tax Table. When must taxpayers use the Rate Schedules instead of the Tax Table to compute their income tax liability?

Q:

Assume that actual overhead costs were $ 8 7 , 0 0 0 and cverhead allocated to jobs was $ 6 3 , 0 0 0 . The unadjusted balance in Manufacturing Overhead would be A . $ 2 4 , 0 0 0 debit B . $ 1 5 0 ,...

Q:

1. How is ethical listening different from listening? 2. "Speaker should consider it their responsibility to educate listeners by introducing ideas of racial, gender, or cultural diversity, but also...