Question: A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds at the ends. If

A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds at the ends. If the plates are subjected to a load of 70 kN, find the size of weld for static as well as fatigue load. The permissible tensile stress should not exceed 70 MPa.

Given Width = 100 mm Thickness = 10 mm p = 70KN = 70 times 10^3N tebsile stress = 70mpa(not exceed) transverse filled welds = 1.5 length of weld for static loading let l = length of weld s = size

Step by Step Solution

★★★★★

3.50 Rating (153 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The question is complete Lets proceed to find the size of the weld for both static and fatigue loads given the permissible tensile stress and the spec... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN, Find the length of weld if the...

A plate 100mm wide and 10mm thick is to be welded to another plate by means of double parallel fillets The plates are subjected to a static load of 80KN Find the length of weld if the permissible...

A blanking disk 0.875 in thick is to be fastened to a spool whose flange is 1 in thick, using eight in-13 X 1.75 in hex-head cap screws. (a) What is the length of threads LT for this cap screw? (b)...

Which one of these sets of cash flows fits the description of an ordinary annuity? O Credit card payments that are paid monthly and equal the amount spent each month O Car payments of $240 a month...

A solid cylindrical shaft with a diameter of 5 0 mm is subjected to a combined loading of a bending moment of 6 0 0 Nm and a torque of 5 0 0 Nm . Determine the principal stresses and the maximum...

Q . 2 ( a ) What do you mean by factor of safety? ( b ) Write short note on maximum shear stress theory and maximum distortion energy theory, Q . 3 Define equivalent twisting moment and equivalent...

Summarize this for me. Someone who understand the HEA and MEA perfectly and also the summary should be 2 or over 2 pages. Someone who understands this perfectly A scrap-tolerant alloying concept...

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

A solid cylindrical shaft with a diameter of 7 0 mm is subjected to a bending moment of 8 0 0 Nm and a torque of 6 0 0 Nm . Calculate the principal stresses, maximum shear stress, and the equivalent...

Refer to Problem E.5. Beth Zion Hospital has just been informed that only the first 10 transplants must be performed at the hospitals expense. The cost per hour of surgery is estimated to be $5,000....

Three different plans for financing a $10,000,000 corporation are under consideration by its organizers. Under each of the following plans, the securities will be issued at their par or face amount,...

Pascal's law states that: Pressure deoreases linearly with depth in a flidd at reit. Presure applied to scondined fails th traverithed und - - inbled in all divetsions. Flud density is always...

Think about a group that you are a member of, and describe the stage of development that your group is currently in. Does the development of this group seem to be following the...

Finley Corporation had income from continuing operations of $10,600,000 in 2012. During 2012, it disposed of its restaurant division at an after-tax loss of $189,000. Prior to disposal, the division...

Mountain Mash produces ice cream for wholesale distribution to grocers, restaurants, and independent ice cream shops. March, April, May, June, and July are busy months for the company as its...

Affordable Lawn Care, Inc., provides lawn-mowing services to both commercial and residential customers. The company performs adjusting entries on a monthly basis, whereas closing entries are prepared...

Fizzy Cola acquired 35% of the voting stock of National Bottlers on January 1, 2014 at a cost of $50,000,000, and reports its investment using the equity method. At the date of investment, National's...

What happens during a short-run economic contraction? A. GDP declines, and unemployment rises. B. GDP rises, and unemployment declines. C. Prices increase without a change in output. D. The economy...

Saturated ethylene glycol vapor at 1 atm is exposed to a vertical plate 300 mm high and 100 mm wide having a uniform temperature of 420 K. Estimate the heat transfer rate to the plate and the...

A cantilever is loaded uniformly on whole span with 1 0 kN / m and a point load of 2 0 kN at free end. Calculate the maximum deflection and slope. The cantilever is 3 m long, 1 0 0 mm wide and 3 0 0...

A slit 1.00 mm wide is illuminated by light of wavelength 589 nm. We see a diffraction pattern on a screen 3.00 m away. What is the distance between the first two diffraction minima on the same side...

Light composed of two spectral lines with wavelengths 600.000 and 600.050 nm falls normally on a diffraction grating 10.0 mm wide. At a certain diffraction angle 0 these lines are close to being...

Please answer in detail with all steps and calculations. Shown in the gure are 4 diffraction patterns such as might be produced by shining laser light (nearly a plane wave) through a slit or slits at...

Question 1 (10 Marks) A furnace wall consists of 200 mm of refractory fireclay brick, 100 mm of kaolin brick, and 6 mm of steel plate. The fire side of the refractory is at 1150 C, and the outside...