Name three players in the construction process

Name four constraints on a construction project:

Name three things codes deal with:

T$/$F Type I has a higher fire resistance than type V

Which is not a correct Masterformat designation?

a$.$ Division $2$ site work b$.$ Division $3$ Concrete c$.$ Division $4$ woods and plastic d$.$ Division $5$ metals

Define$-$ Occupancy group

Name three factors that affect allowable building area

Define: cladding

Name three forces that move water

Which is generally not used as a sealant?

urethane b$.$ silicon c$.$ butyl rubber d$.$ mastic

Backer rod is used to prevent:

T$/$F Most cladding today is not load bearing:

Name three advantages of masonry:

Define: spandrel

Name four cladding systems

Name two coatings for aluminum finishes

T$/$F Aluminum is not easily extruded but usually hot rolled.

T$/$F Small amounts of electricity are used in the production of aluminum.

Which is not a mode of aluminum system assembly?

stick b$.$ design$/$build c$.$ unit d$.$ panel

$20.$ Framing members in a metal and glass system are called $\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_.$

$21.$Name a consideration for an outside versus an inside glazing system.

$22.$ T$/$F Most expansion joints for a metal and glass system are built in$.$

$23.$ T$/$F Purlins go on the wall.

$24.$ Name four parameters of a finish system.

$25.$ Finishes usually start after $\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ is installed.

$26.\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ are usually the last item completed on a conventional project.

$28.$ Name three considerations for interior finishes.

$29.$ Name four factors concerning durability of interior finishes.

$30.$ Name three ratings concerning combustibility.

$31.$ Fire resistance ratings are given in $\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_.$

$32.$ With respect to interior finishes name three factors concerning mechanical systems.

$33.$ Name four current trends in interior finishes.

$34.$ Which is not an interior partition requirement?

a$.$ within budget b$.$ durable c$.$ appropriate acoustics d$.$ transmissibility

$35.$ Name three types of interior partitions.

$36.$ Name three partition back$-$up materials.

$37.$ T$/$F Plaster is an inexpensive material with good fire resistance.

$38.$ T$/$F Portland cement and lime is the most common mix for interior finishing plaster.

$39.$ Lathing can be made from which of the following:

a$.$ wood strips b$.$ expanded steel c$.$ plywood d$.$ plaster board

$40.\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ is the most common currently used lathing material.

$41.$ Name the three coats in a lath and plaster system.

$42.$ T$/$F Plaster can be applied directly over cmu.

$43.\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ is the most common and least expensive interior finish sytem.

$44.$ There are $\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ levels of specified wall board finish.

$45.$ Masonry partitions were historically made from $\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_.$

$46.$ Name three ceiling finish systems.

$47.\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ is used by hospitals and labs for extensive mechanical systems.

$48.$ Name three considerations for choosing an interior flooring system.

$49.\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ tile are typically large $(1$x$1)$ and unglazed.

$50$ Besides plain concrete $\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_$ is the least expensive flooring material.