Question: need help using excel s6.7 Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter'is a critical factor

need help using excel need help using excel s6.7 Auto pistons at

s6.7 Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter'is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x ? b) What is the value of R ? c) What are the UCLx and LCLx, using 3 ? Plot the data. d) What are the UCLR and LCLR, using 3 ? Plot the data. e) If the true diameter mean should be 155mm and you want this as your center (nominal) line, what are the new UCLx and LCLx ? Px

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Please show all or any work needed. Please answer all parts. S6.7 Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must...

Please show specific hand calculations. 1.) REQUIRED PROBLEM S6.7 on page_268 [20 points) (NOTE: This is similar to Problem S6.6 X-Bar & R-Bar Charts done in lecture.) (a.) Do Problem 56.7 on page...

71" 8.11 000 W 8 11 283 1.58 56.6 Sampling four pieces of precision-cut wire (to be used in computer assembly) every hour for the past 24 hours has pro- duced the following results: HOUR R HOUR 1 325...

dont plot the data, thank you. S6.7 Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample...

S6.7 Auto pistons at Wemming Chungs plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each...

..S6.7 Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced...

e) If the true diameter mean should be 155 mm and you want this as your center (nominal) line, what are the new UCL x and LCL x ? Upper Control Limit (UCL x ) = ? mm (round your response to two...

auto pistons at wemming chung plant in shangai are produced in a forging process, and the diameter is a critical factor that must be controlled. from sample sizes of 3 pistons produced each day the...

b) what is the value of R c) what are the UCLx and LCLx using 3 sigma d)what are the UCLSr and LCLr using 3 sigma Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process,...

Auto pistons at Wemming Chung plant in Shanghai are produced in a forging process and the diameter is a critical factor that must be control Prom sample sizes of pestons produced each day, the mean...

How does the asset structure of credit unions compare with the asset structure of commercial banks and savings institutions? Refer to Tables 2-6, 2-10, and 2-13 to formulate your answer.

Use the same population of {2 min, 3 min, 8 min} from Exercise 45. Show that when samples of size 2 are randomly selected with replacement, the samples have mean absolute deviations that do not...

Prepaid Expenses is classified as a [ Select ] [ " Current Asset", "Non - Current Asset", "Current Liabiity", "Non - Current Liability", "Owner's Equity", "Revenue", "Expense" ] and is reported in the

As the manager of Smith Construction, you need to make a decision on the number of homes to build in a new residential area where you are the only builder. Unfortunately, you must build the homes...