Question: OUESTION TWO a ) A centrifugal pump with impeller diameter 5 0 0 mm is designed for a discharge of 1 . 0 m 3

OUESTION TWO
a) A centrifugal pump with impeller diameter 500 mm is designed for a discharge of 1.0m3s of water. The water enters the pump axially, leaving the impeller with an absolute velocity of 12ms at an angle of 20 to the tangent at the impeller periphery. The impeller is rotating at 700 rpm . Determine the exit vane angle and the hydraulic power delivered. (6 marks)
OUESTION TWO a ) A centrifugal pump with impeller

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Maple Leaf Foundary, owned by Ahmet Satir, produces cast-iron ingots according to a 3-month capacity plan. The cost of labor averages $100 per regular shift hour and $140 per overtime (O.T.) hour....

Q:

c ) A liquid fuel with a density of 8 6 3 kg m - 3 and a flow rate of 0 . 7 m 3 s - 1 is to be delivered by the operating pipeline of 1 0 , 8 8 2 m long. The annual charges ( interest on capital,...

Q:

A system pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.245 m and the pipe lengths are L1= 5 m, L2= 3 m, L3= 3 m, and L4= 0.3 m. The impeller of the centrifugal pump...

Q:

A water turbine is to be designed to produce 27 MW when running at 93.7 rev/min under a head of 16.5 m. A model turbine with an output of 37.5 kW is to be tested under dynamically similar conditions...

Q:

The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 4.5 m, L2= 3.5 m, L3= 2.5 m, and L4= 0.5 m. The impeller of the...

Q:

a) What would be the shaft power required to turn the impeller if the exit blade angle is 37 degrees. The value of the shaft power is

Q:

A system pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.245 m and the pipe lengths are L1= 5 m, L2= 3 m, L3= 3 m, and L4= 0.3 m. The impeller of the centrifugal pump...

Q:

just need the answers of 4.4, 4.9, 4.11, 4.12 and 4.14 Problems 107 P. 51 5 4.3 A centrifugal pump is required to develop a pressure rise of 30 psi when delivering 1000 gpm. If three motors with...

Q:

The pumping system to be designed is as shown in Figure 13.41 on page 348 of the Mott text, seventh edition. All data for this problem is as shown in Fig. 13.41 with the one revisio of a discharge...

Q:

Pump will be installed next to the turbine unit at the bottom of the hill. Centrifugal pump will be used for pumping the water from the sea to the upper reservoir during the period when excess...

Q:

Standards and Pump HW You need to deliver 300 L/s of water at 20 C from a large, constant-level tank to another constant-level tank as shown in the figure. A centrifugal pump from the...

Q:

The stated yield to maturity and realized compound yield to maturity of a (default-free) zero-coupon bond will always be equal. Why?

Q:

Jarrod has an old TV worth about $ 100. Jarrods other assets total about $ 150. What is Jarrods debt to asset ratio? What does this indicate about Jarrods financial position?

Q:

When a business for sale is no longer a going - concern due to declining profits, a liquidation value can be determined using Multiple Choice the contingent business value method. the earnings...

Q:

Introduction: In Chapters 1, 3, and 15, you examined some of the laws impacting the human resources function. In this assignment, you will read a scenario and identify the laws and actions to be...