Question: P 9 . 2 4 Calculate the vertical deflection at point A and the horizontal deflection at point B . I = 2 0 0

P9.24 Calculate the vertical deflection at point A and the horizontal deflection at point B.I=2000 in ?4.Must use virtual work methods!!
P 9 . 2 4 Calculate the vertical deflection at

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

please answer using castiglianos method if not then I will unlike, if you do i will like. Possible answers: ( 6 P I ^ 3 ) / ( 2 5 EI ) + ( 1 3 P I ) / ( 2 E A ) , ( 6 P I ^ 3 ) / ( 5 E I ) + ( 3 PI )...

Q:

a ) Use the principle of virtual work to calculate the vertical deflection at point 4 . Both beams have the same E I = 3 6 , 0 0 0 k N . m 2 and both are inextensible. The tie rod has E A = 2 5 , 0 0...

Q:

A uniform rod of flexural rigidity El is loaded as shown below. Given: \ ( \ mathrm { P } , \ mathrm { E } , \ mathrm { I } \ ) , crosssectional area A , Young's modulus E , and length \ ( l \ ) ....

Q:

1 . Determine the support reaction at \ ( A \ ) ( fixed end ) and \ ( C \ ) ( roller ) 2 . Draw the Shear \ ( ( \ mathrm { V } ) \ ) and Bending Moment \ ( ( \ mathrm { M } ) \ ) diagrams for the...

Q:

9.3 1)Listed below are body temperatures from five different subjects measured at 8 AM and again at 12 AM. Find the values of d and sd. Ingeneral, what does d represent? Temperature(F)at8AM 98.3 99.2...

Q:

Repeat Prob. 482 for the vertical deflection at point A. Prob. 482, The part shown is formed from a 1/8 -in diameter steel wire, with R = 5 in and l = 4 in. A force is applied with P = 1 lbf. Use...

Q:

* * Thoroughly do and show all work on each bulletin point with explanation, thank you!!! * * Exercise 2 : Straight beams: Strain Energy methods A beam defined in figure below, is submitted to a...

Q:

The simply supported beam is pin supported at point A and roller supported at point C and subjected to the point load shown. If the moment of inertia of the cross sectional area of the beam is 4 0 0...

Q:

Exercise 2 : Straight beams: Strain Energy methods A beam defined in figure below, is submitted to a partial distributed load w between ( AB ) , and a single load F at point C . The characteristics...

Q:

Repeat Prob. 481 for the vertical deflection at point A. Prob. 481, The part shown is formed from a 1/8 -in diameter steel wire, with R = 5 in and l = 4 in. A force is applied with P = 1 lbf. Use...

Q:

What are the major factors to consider in individual decision making? Related to this type of decision making, please consider the following questions: What are the four Jungian decision styles, and...

Q:

Consider an ideal gas-turbine cycle with two stages of compression and two stages of expansion. The pressure ratio across each compressor stage and each turbine stage is 8 to 1. The pressure at the...

Q:

10. What differences are there between the trial balance before closing and the trial balance after closing with respect to the following accounts? a. Accounts Payable. b. Expense accounts. c....

Q:

JDD Corporation provides the following benefits to its employee, Ahmed (age 49): Life insurance Salary Health insurance Dental insurance Dependent care Professional dues $ 366,000 17,400 4,500 3,600...