Question: Part A Consider the beam shown in ( Figure 1 ) . Support B settles 5 m m . Take E = 2 0 0

Part A
Consider the beam shown in (Figure 1). Support B
settles 5mm. Take E=200GPa and
I=500(106)mm4.
Determine the x and y components of reaction at the pin at A.
Express your answers in kilonewtons to three significant figures separated by a comma.
Part B
Determine the y component of reaction at the roller at B.
Express your answer to three significant figures and include the appropriate units.
Figure
Part A Consider the beam shown in ( Figure 1 ) .

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

show calculation Review Part A Consider the beam shown in (Figure 1). Suppose that w = 65 N/m. Determine the horizontal and vertical components of reaction at support A Express your answers in...

Q:

Part A Consider the beam shown in ( Figure 1 ) . Assume that E I is constant. Follow the sign convention. Determine the equation of the elastic curve for the beam using the x coordinate. Express your...

Q:

Part A Consider the beam shown in (Figure 1). Suppose that w1 = 950 N/m and w2 = 600 N/m Determine the y component of reaction at A using scalar notation. Express your answer to three significant...

Q:

Part A - Finding the vertical component of the reaction at A Learning Goal: To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for Determine the...

Q:

Consider the beam shown in ( Figure 1 ) . The support at B settles 0 . 1 5 f t . E = 2 9 ( 1 0 3 ) k s i and I = 7 5 0 0 i n . ? 4 Assume the supports at B and C are rollers and A is fixed. Figure...

Q:

Consider the beam shown in ( Figure 1 ) . Use the conjugate - beam method. Take E = 2 0 0 GPa, I = 5 5 0 ( 1 0 6 ) mm 4 . Suppose that P = 5 1 kN . Determine the slope at B measured counterclockwise...

Q:

Consider the beam shown in ( Figure 1 ) . Take P 1 = 2 4 k N , P 2 = 1 8 k N , w 1 = 1 6 k N m , and w 2 = 2 k N m . The frame is pin connected at A , B , and C , and the two joints D and E are fixed...

Q:

Consider the beam shown in (Figure 1). Suppose that the distributed load intensities w = 80 lb/ft and W2 35 lb/ft. Follow the sign convention. = Figure 1 of 1 12 ft -15 f D 690 lb SA1 10 ft Determine...

Q:

Consider the beam shown in ( Figure 1 ) . Suppose that w 1 = 6 3 0 N m and w 2 = 4 2 0 N m . Figure 1 of 1 Part B Determine the x and y components of reaction at B . Express your answers in...

Q:

View Available Hint ( s ) Consider the beam shown in ( Figure 1 ) . Suppose that w = 9 5 0 N m for Part A for PartA Wido for Part ? b a r ( 4 ) redo forPart A reser for Part A keyboard shortcuts for...

Q:

Where would you place the product/service in the Product Life Cycle (PLC) graph? And why (give reasons)? Where would you place the product/service in the BCG model? And why (give reasons)?r

Q:

My company is Tesla and Ford Motor and General Motors are my competitors. Assuming all companies published their 2022 annual reports, your three-year trend should include the following years 2022,...

Q:

Question 1 2 ( 5 points ) In the constant growth model, if a stock's dividend is expected to grow at a constant rate of 5 % a year, which of the following statements is NOT CORRECT? Assume the stock...

Q:

10 Required information [The following information applies to the questions displayed below.] Delph Company uses a job-order costing system and has two manufacturing departments-Molding and...