Question: Problem 1 . The continuous reinforced concrete beam is loaded as shown in the figure. Draw the shear and moment diagrams. Use Moment Distribution Method

Problem 1.
The continuous reinforced concrete beam is loaded as shown in the figure. Draw the shear and moment
diagrams. Use Moment Distribution Method (6 cycles/distributions), Determine the following:
Moment at A in KN.m.
Moment at C in KN.m.
Vertical reaction at B in KN .
Vertical reaction at D in KN .
Determine the maximum shear force in KN .
Direction and degree of the moment diagram curve between A and B.
Maximum positive moment in KN.m.
Problem 1 . The continuous reinforced concrete

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Problem No.2 Beam is loaded as shown in figure below. Neglect the weight of the beam. w = 200x N/m !!! B 2m A. Determine the following: (1 point each) a.) The support reaction at point A. b.) The...

Q:

Reinforced concrete Design (e) Sectional vien calone XXr of the leams shewine the 156mm thick alah Herure 1. Analssis and decien of reinforced concrete heams Deweret The general fay-out of the...

Q:

Instructor: Ameh Fioklou, Ph.D., P.E. 1 of 7 CE 310 Elementary Structural Analysis Final Project Computer Applications Fall 2021 The objective of this project is to get you familiar with structural...

Q:

use the m-fileShearAndBending (M)to plot a shear and bending moment set of graphs. You will need to enhance the plot with labels, titles and more. The figure for sample problem 7.4 without...

Q:

Consider the beam assembly shown below Two horizonal beam member A B and B D are connected by a double shear pin at B Note that points A and D are a simple roller and pinned supports respectively A 1...

Q:

use the m-fileShearAndBending (M)to plot a shear and bending moment set of graphs. You will need to enhance the plot with labels, titles and more. The figure for sample problem 7.4 without...

Q:

use the m-fileShearAndBending (M)to plot a shear and bending moment set of graphs. You will need to enhance the plot with labels, titles and more. The figure for sample problem 7.4 without...

Q:

Summary: Shear and Moment Diagrams with "Shortcut" Method Figure 1 shows a beam with a pin support at A and a roller support at B. The beam is subjected to four applied loads as shown below (two...

Q:

For the beam structure shown below, find all support reactions, draw the Shear Force Diagrams and the Bending Moment Diagrams (assuming El is constant for all members) using the following methods and...

Q:

A single concrete frame layout and cross section is shown in Figure 1 and Figure 2 respectively to be analysed with the Portal, Cantilever and Moment Distribution Methods. a. Explain the differences...

Q:

For an NMOS transistor, for which V t = 0.4 V, operating with v GS in the range of 0.8 V to 1.8 V, what is the largest value of v DS for which the channel remains continuous?

Q:

Molecules enter a cell at a rate of 0.045 per second. What is the probability that between 150 and 200 molecules enter during an hour? Use the normal approximation to the Poisson distribution with...

Q:

Baker, Inc. has two service departments ( Information Technology and Administration ) and two user departments ( Department A and Department B ) . Administration uses 5 0 % of the total services...

Q:

Pearl Products Limited of Shenzhen, China, manufactures and distributes toys throughout South East Asia. Three cubic centimeters (cc) of solvent H300 are required to manufacture each unit of...