Question: Problem 2 . Determine the support reactions for the indeterminate beam using the force method and then sketch the shear force and bending moment diagrams.

Problem

2 .

Determine the support reactions for the indeterminate beam using the force method and then sketch the shear force and bending moment diagrams. Release the roller at B

.

There will be two primary systems. Evaluate deflections using the deflection tables. EI is constant over the beam. Answer to check:

B_{y} = 32.25 k .

Problem 2 . Determine the support reactions for

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Problem 3 . Determine the support reactions for the indeterminate beam using the force method and sketch the bending moment diagram. Assume A is pinned and B and C are rollers. Take E I = constant...

Problem 4 . Determine the support reactions for the indeterminate frame using the force method and then sketch the bending moment diagram. Assume both A and C are pins and joint B is fixed. Take E =...

Determine the support reactions of the following beam using the force method, then draw the shear force and bending moment diagrams. Consider only the effect of bending moment. EI is constant. ( 6 0...

Live Loads Allinterior floors 2 . 5 kN / m 2 Roof and Cantilevers 1 . 5 kN / m 2 Assume that design wind loadand earthquake loadare negligible for location of the building structure. Floor Slab...

Problem 2 : The support at B settles by 1 2 i n . Determine the reactions and draw the shear and bending moment diagrams for the beam shown below by using the slope - deflection method. 1 5 ft 1 5 ft...

1 5 CMMCE Vew York Cily Collage of Technolowy Construction Management & Civil Engineering Technology CMCE 1 2 1 5 Strength of Materials Fall 2 0 2 4 Prof. I. Guzman, PhD , P . E . Project Wood...

Beam ABCDEFG of total length 3 6 m is supported at A , B , F and G . The beam is hinged at point C and E and loaded as shown in Figure Q 1 a and the beam cross - section in Fig. Q 1 b 1 Calculate the...

Calculate the support reactions. Draw the shear force and bending moment diagrams. Determine the maximum bending moment and shear force and their corresponding locations from point A ? Calculate the...

Problem 2 : Force method - Moment Area For the indeterminate beam shown below, use the force method to determine redundant support reaction, then solve other reactions and sketch moment and shear...

g) h) 5 KN 50 mm 20 mm 150 mm 40 mm 2 kN 200 mm 5 kN 1 kN Three forces are applied to member ABD as shown. The cross-section is a hollow rectangle with 20mm height and 40mm width and a wall thickness...

Explain the difference between a Ferromagnet and a paramagnet on the basis of macroscopic measurements. What is the saturation magnetization and how does it differ as a material is heated through its...

Assume there are 3 types of squirrels in the world (red, black, grey). Assume 40% of squirrels are black, 40% of squirrels are grey and 20% are red. Assume 3% of red squirrels are in Ontario, 2% of...

For any ratio that shows a year - to - year difference of 1 0 % or more, state whether the difference is in the company's favor or not. Part 1 7 Indicate whether the proportional difference is in the...

Because underwriters must gather and process information efficiently, they should make the best possible use of the information immediately available. The two sources of information that are...