Question: Problem 3 A beam ABC is subjected to uniformly distributed load q = 3 0 0 N m on span A B and point load

Problem 3
A beam ABC is subjected to uniformly distributed load q=300Nm on span AB and point load P=10
kN at C. The beam has flexural rigidity El=1.5107N-m2 and the length L=6m.
Using the superposition method, determine the deflection at point C.(downward positive)
Answer:
c(mm)=
Problem 3 A beam ABC is subjected to uniformly

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Figure Q1 shows an overhanging beam with pin support at point A and roller support at point B. The beam is subjected to uniformly distributed load from point A to point B and concentrated load at...

Q:

A steel cantilever beam, of length 2L, has an l-section, see Figure Q3. The cantilever beam is under a uniformly distributed load q = 250 kN/m applied in its vertical plane of symmetry at OA part of...

Q:

A steel cantilever beam, of length 2L, has an l-section, see Figure Q3. The cantilever beam is under a uniformly distributed load q = 175 kN/m applied in its vertical plane of symmetry at OA part of...

Q:

Question 3 A steel cantilever beam, of length 2L, has an I-section, see Figure Q3. The cantilever beam is under a uniformly distributed load q = 195 kN/m applied in its vertical plane of symmetry at...

Q:

A steel cantilever beam, of length 2L, has an I-section, see Figure Q3. The cantilever beam is under a uniformly distributed load q = 285 kN/m applied in its vertical plane of symmetry at OA part of...

Q:

Calculate the deflection at point C of a beam subjected to uniformly distributed load w = 275 N/m on span AB and point load P = 10 kN at C. Assume that L = 5 m and EI = 1.50 X 10 7 N.m 2 . A W -L- B...

Q:

Figure Q 3 Question 3 A steel cantilever beam, of length 2 L , has an I - section, see Figure Q 3 . The cantilever beam is under a uniformly distributed load q = 2 6 0 kN / m applied in its vertical...

Q:

There are three supports at point B, C, and D along a beam. The beam is subjected to a distributed load, q of 12kN/m and a point load P of 1000N as shown in Figure 2. The beam has modulus of...

Q:

Problem 2 The roof of a residential building as shown below is Subjected to uniformly distributed load of 1 . 5 kPa . According to the concept of tributary areas, a ) Shade the tributary area for the...

Q:

Figure 10.23 shows a circular area of radius, R = 5 m subjected to a uniformly distributed load, q = 380 kN/m2. Determine the vertical stress increases 3 m below the loaded area at radial distances,...

Q:

Determine the unknown quantity for each of the following independent situations using the appropriate interest tables: 1. Sue wants to have $10,000 saved when she begins college. If Sue enters...

Q:

From the following information, construct a bank reconciliation for Faith Co. as of July 31, 2013. Then prepare journal entries if needed. Ending G/L Cash balance $445 Ending bank statement balance...

Q:

If an analyst estimates a quality of earnings ratio of 0 . 8 , what does this imply about the company? Group of answer choices The company may be aggressive in its revenue recognition policy The...

Q:

Scorpion Corporation makes three products in its factory: hammers, wrenches, and saws. The overhead costs for the fiscal year are as follows: Item Activity Cost Pool Cost driver Machine setups...