Question: Problem 4 ) Using the method of sections, find the force in members CD , DM , and LM of the truss shown in the

Problem 4)
Using the method of sections, find the force in members CD, DM, and LM of the truss shown in the sketch below. Be sure to indicate if the force is tension or compression. Note that each member (except member EL) has a length of one meter. The left support (at joint A) is a hinge, and the right support (at joint I) is a roller.
Problem 4 ) Using the method of sections, find

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Problem 5: Method of Sections d Inputs: d = 4 m A B D E F D M H 1 J K L a a 3 m (all horizontal members are this length) P = 45 kN P There is a pin at A and a roller at G. Using the method of...

Q:

Problem 4. Determine the load in member AB of the pin-connected truss shown in Figure 4. 3 m 3 m 1 m 4 m A 2m 8 15 68 kN E FIGURE 4 Problem 5. Using the method of sections, determine the loads in...

Q:

Problem 4 A simple truss is shown. Using the Method of Sections, calculate the force in members E F , C F , and B C . State if the member is in tension or compression. Summarize your calculations in...

Q:

Problem 4 A simple truss is shown. a . Using the Method of Sections, calculate the force in members EF , CF , and BC . State if the member is in tension or compression. Summarize your calculations in...

Q:

FIGURE 4 Problem 5. Using the method of sections, determine the loads in members BD, CD, and CE of the truss shown in Figure 5. 2.5' FIGURE 5 2.5 kips 5 3 2.5 = 22.620 Emer-0-8.5A +2.5 (2.5)-2(1) 1...

Q:

Question 2 : For the following truss: a ) Calculate the degree of static indeterminacy ( SI ) and state if is determinate or indeterminate. b ) Find any zero force members and clearly mark them on...

Q:

(2) Truss Analysis by Hand using Method of Sections (20 pts) Consider the truss structure shown in Figure 2. The magnitude of F is 25 kN. Your solution for this problem should include assumptions,...

Q:

ASSIGNMENT 4 1. Find the tension in cables AB, BC, CD and EC. E C D A B 30 125 kg 2. Find the forces in beams AB (FAB) and AC (FAC). B 2 m 4 m A 4 m im 75 KNASSIGNMENT 5 1. Find the reactions at A...

Q:

06.04 Frames Pt 2 Video Solution Problem - Forces in a Truss Method of Sections Watch the following video, then answer the question(s) Part A 50 KN 50 kN 50 kN bu bx bx M L K JIH N CL50 kN T, ML =...

Q:

Problem # 4 - Truss Analysis ( 2 parts, 2 0 total points ) The king post truss shown below is loaded with a 1 2 6 kN force acting downward at point F , and a 5 7 kN force acting to the right at point...

Q:

This exercise should be used with Exercise 1-30B. In Exercise 1-30B, Amounts of the assets and liabilities of Diaz Design Company, as of July 31, 2014, are as follows. Also included are revenue,...

Q:

Given that the total cost function is: TC = 100Q Q^2 + 1 / 3Q^3 where Q = rate of output and TC = total cost 1 Determine the marginal and average cost functions. (4 marks) 2 Calculate the output...

Q:

Both Traditional IRAs and Roth IRAs create tax advantages and have annuat contribution limits . favor the appreciation of principal. favor capital appreciation. are taxed at distribution. have...

Q:

Altira Corporation provides the following information related to its merchandise inventory during the month of August 2021: Aug.1 Inventory on hand-2,500 units; cost $6.60 each. 8 Purchased 12,500...