Question: Problem (5) A muff coupling is connecting two shafts for transmitting 650 Nm torque. The shafts' diameter is 45 mm and the square key

Problem (5) A muff coupling is connecting two shafts for transmitting 650 Nm torque. The shafts' diameter is 45 mm and the square key dimensions are 14 mm width and 110 mm length. Find the following:- a- Muff outer diameter (its material is cast iron of 30 MPa allowable shear strength) b- Key stresses (shear and crushing)

Step by Step Solution

★★★★★

3.48 Rating (148 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

ANSWER AND EXPLANATION a The outer diameter of the muff couplin... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A torque of 650 Nm rotates a shaft of diameter 0.25 m with = 50 rad/s. What are the shaft surface speed and the transmitted power?

A hollow spherical iron container whose outer diameter is 40 cm and thickness is 0.4 cm is filled with iced water at 08C. If the outer surface temperature is 38C, determine the approximate rate of...

Henry is about to move into a new house and needs to arrange to have the internet connected. After doing some research about the best internet plans and providers, he contracts an internet supplier...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Problem Statement: It is required to design a pin bush type flexible flange coupling to connect two shafts. The input shaft transmits 1 0 kW power at 1 8 0 rpm to the output shaft through the...

Question 6 . [ 5 Marks ] You are required to connect two parallel shafts with a par of gears. The shafts are a distance a apart from each other. Figure 6 : A pair of gears connecting two shafts ( a )...

Repeat Problem 5. Assume that the shaft connecting gears 1 and 2 is relatively short and rigid. Data From Problem 5: A three-degree-of-freedom gear-train system is shown in Figure 5.101, which...

Question 12 (3 points) What is a VLAN? A/ Question 13 (5 points) Assume you are connecting two machines over a network with 1Gbps bandwidth and 60ms round-trip time. If the sender always sends at the...

Problem 5 A reversed curve is connecting the two tangent lines A B and C D having directions of due east and S 6 0 E respectively. The radius of the first curve at A which is also the P . C . is 2 0...

A family friend has asked your help in analyzing the operations of three anonymous companies operating in the same service sector industry. Supply the missing data in the table below: Note: Loss...

The properties of unidirectional fiber reinforced polymer composite laminate are given as: Elasticity modulus E (GPa) Shear modulus G(GPa) Fiber (E1f)=252 (E2f)=30 25 0.32 Matrix 3,8 2 0.28 Poisson's...

Graph the function. y= se2x To draw the graph, plot three consecutive asymptotes and two points, one on each side of the second asymptote. Then click on the graph icon.

Which circuit below is a direct implementation of the propositional logic statement ~ (p V qV ~ (r^ ~ ))^\\ ~ r? Version 1 P 13 P output 9 Version 2 output R

Golebiewski Corporation has provided the following contribution format income statement. Assume that the following information is within the relevant range. Sales (5,000 units) $150,000 Variable...

Find the stable reactor period for the zero-power reactor whose no response is shown in Figure 1.35 1.3 1.25 1.2 1.15 1.1 1.05 1 0 0.25 0.5 0.75 Time (s) 1 1.25 1.5

3. Compute invoice price of the following positions for settlement date Sept 10, 2016: (Do not use the excel formula 'ACCRINT' for accrued interest) Position Maturity Bid Discount Coupon Rate 1.06590...

Consider the setup in Problem 16. Show that the relative speed of the ball and the point of contact on the stick is the same before and immediately after the collision. (This result is analogous to...

A utility hook was formed from a round rod of diameter d = 20 mm into the geometry shown in the figure. What are the stresses at the inner and outer surfaces at section AA if F = 4 kN, L = 250 mm,...

Repeat Prob. 3 15 for: (a) x = 8MPa, y = 7MPa, xy = 6MPa cw (b) x = 9MPa, y = 6MPa, xy = 3MPa cw (c) x = 4MPa, y = 12MPa, xy = 7MPa ccw (d) x = 6MPa, y = 5MPa, xy = 8MPa ccw

In the figure shown, shaft A, made of AISI 1020 hot-rolled steel, is welded to a fixed support and is subjected to loading by equal and opposite forces F via shaft B.A theoretical...

What are the three primary colors as proposed by the trichromatic theory? a. red, green, blue b. red, yellow, blue c. white, black, brown d. white, black, red

Colleen stares at a fixed spot in her bedroom using only one eye. After a while, what might happen to her vision? a. Objects will become more focused the longer she looks at them. b. Any object she...

In farsightedness, also known as _____________, the focal point is _____________ the retina. a. presbyopia; above b. hyperopia; beyond c. myopia; below d. presbyopia; in front of