Question: Problem. For the beam and loading shown in Fig., use the double - integration method to determine ( a ) the equation of the elastic

Problem. For the beam and loading shown in Fig., use the double-integration method to determine (a) the equation of the elastic curve for the entire beam, (b) the deflection at C, and (c) the slope at B. Assume that El is constant.
(Ans: v=-w(4L-x)424EI-2wL3x3EI+49wL424EI,B=wL32EI,VC=-5wL48EI)
Problem. For the beam and loading shown in Fig.,

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Question - 2 : P 1 0 . 1 9 For the beam and loading shown in Fig. P 1 0 . 1 9 , use the double - integration method to determine ( a ) the equation of the elastic curve for the entire beam, ( b ) the...

Q:

Use double integration Method to set elastic curve, slope eq a dellection at B E = 1 0 , 0 0 0 k s . I = 4 0 0 1 . Use double - integration method to determine 1 ) the elastic curve of the beam; 2 )...

Q:

Problem 2 : For the beam shown below, ( a ) use method of integration to determine equation of elastic curve for the beam. Assume EI is constant for the beam, ( b ) find the slope at point A and...

Q:

Problem 1 : For the beam shown below, ( a ) use method of integration to determine equation of elastic curve for the portion A B of the beam, ( b ) find the deflection and slope at point B . Assume E...

Q:

2 5 % score reduction after attempt 4 Part 5 X Incorrect Integrate your equation for M ( x ) on segment B C twice to find the equation for the slope and for the elastic curve. Each integration will...

Q:

The length of a bar in a simply supported beam is 8 m. It is subjected to UDL of 20 kN/m over the whole span and deflects 5 mm at the centre. Find the value of the product EI for the above beam....

Q:

The beam ABCD is loaded as shown. Use the following values in your working out: L = 650 mm F = 10 KN w = 6 kN/m 1 B 3 I L 'c a) Using discontinuity functions/Macauley brackets, write the bending...

Q:

For the beam and loading shown, use the double - integration method to determine ( a ) the equation of the elastic curve for segment A B of the beam, ( b ) the deflection at B , and ( c ) the slope...

Q:

Determine the equation of the elastic curve for the simply supported beam shown below using the given x coordinate, where 0 x L 2 . Also, using the double integration method, determine the slope at A...

Q:

For the cantilever beam and loading shown, using method of integration (and singularity functions), determine: a. the equation of the elastic curve of the beam b. the deflection at B c. the slope at...

Q:

An isosceles triangle has two equal sides of length 13 cm. Determine the maximum possible area of the triangle. The answer is 84.5cm^2

Q:

FIFO and average-cost are the only two acceptable cost flow assumptions permitted under _________. a. IFRS b. GAAP

Q:

Tuscaloosa National Banik has two service departments, the Haman Resources ( H 2 ) Departmert and the Computing Department. The bank has two other departmemts thet drectly service customers, the...

Q:

Instructions Chart of Accounts General Journal Balance Sheet Instructions IFRS White Corporation has entered into an agreement to transfer accounts receivable to Murphy Company. Under the terms of...