Question: PROCEDURE Part 1: POWER SUPPLY TESTING 1.1 - Plug the trainer into a 120VAC outlet and set the power switch (29) to the ON position.

PROCEDURE Part 1: POWER SUPPLY TESTING 1.1 - Plug the trainer into a 120VAC outlet and set the power switch (29) to the "ON" position. The red LED (19) will light when the unit is on. 1.2 - From the Power supply section change both knobs (6 and 7) counterclockwise. 1.3 - Turn on the digital multimeter (DMM) and set it to measure DC Voltage. 1.4 - Connect the digital multimeter terminals to the POS (5) and GND (4) of the Power supply and measure the voltage. Record your reading in column 1, T ABLE 1. 1.5 - Turn the POS knob (6) all the way clockwise and measure the voltage. Record your value in column 2, T ABLE 1. 1.6 - Turn the knob to the 5 V indicator. Record the exact value in column 3, T ABLE 1. Power Supply Minimum Voltage Maximum Voltage Controlled 5V DMM Reading DC Voltage (Vdc) Table 1 - Voltage Measurements - Power Supply School Of Engineering Technology and Applied Science (SETAS) Advanced Manufacturing and Automation Technology (AMAT) EET123- Lab instruction Experiment No. 0 Digital Box Trainer Fall 2023 Rev 1.0 Section: Group: Name and ID# Name and ID#

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Physics Questions!

need help to write a Conclusion for this experiment , brief is provieded mentioning we observed this, we observed that, we obtained this.... is not enough. In this section, you should also highlight...

Need a help on writing a conclusion for heat exchanger experiment Experiment HE: Heat Exchangers Objective To investigate the effect on the overall heat transfer coefficient and on the effectiveness...

Power Supply Digital Multi-meter Vcc +12 V Procedure Part 1- Simple Switch Circuit R 1 K Red LED Step 1.1 - Set the DMM to measure the resistance. Measure R1 and R2 resistance and enter the values in...

This Is a lab Manual That you can use to answer the questions. I'm really confused about the questions I would really appreciate it if you can help I have an exam on this lab so I need correct...

read the lab and solve the lab questions then write a typed lab report following the "lab report outlier" as a quide. forget last post and just answer lab questions Digital Trainer Familiarization...

Question: TBD=42 Scenario Details The "Automated Parcel Delivery" company is examining a proposal to provide a drone parcel delivery service for supermarkets across the Perth Metropolitan area. It...

Please read the question Question : What are "spaced practice", "varied practice", and "interleaved practice"? Give a definition for each. Then give an example of each from your own experience as a...

Answer all questions and calculations please! Lab 19: External Forces and the 3rd Law Force Sensor String Elastic Cord PASCOL PASCO Figure 1. The two carts are accelerated to the right by pulling on...

Hello I'm trying to write a report after collecting this data about conservation of energy and momentum. Please any help would be much appreciated Data Sheet for Experiment M-9 4. Plug the small plug...

CECS 346 Project 3 A Smart Home By Dr. Min He Preparation: You will need two LaunchPads, 3 stepper motors with drivers (can be checked out from the instructor), 2 obstacle avoidance sensors (can be...

You perform some experiments for the reaction A B + C and determine the rate law has the form Rate = k[A]x Calculate the value of exponent x for each of the following. a. [A] is tripled and you...

The following information relates to Helena Limited: Required: Calculate the following accounting ratios for each of the five years from 30 April 2008 to 2012 inclusive: (a) Gross profit (b) Mark-up...

Amita has 3 children ages 2 , 5 , and 7 . The current cost of college is $ 3 0 , 0 0 0 . The children will begin college at age 1 8 and be in college for 5 years. Education inflation is expected to...

Shown below are units produced and total manufacturing costs for the past four months at Minga Manufacturing Corporation: What is Minga's cost formula for total manufacturing cost under the high-low...

With the previous strategy (#1) in your mind, think about your own group memberships and how they affect your verbal and nonverbal communication style. When you are interacting with people from...

What are some of the groups to which you would like to belong but do not?

How does society perceive the groups to which you belong? Favorably or unfavorably? In other words, by virtue of your membership in these groups, how are you treated by others?