Question: Q 2 : Determine the Force in member 2 - 4 of the steel truss shown in Figure 2 , using Force Method. The stiffness

Q2:
Determine the Force in member 2-4 of the steel truss shown in Figure 2, using
Force Method. The stiffness EA is the same for all the members.
Note:
Determine all required internal actions in the members using the pin-
joint method or the method of sections for Real and Unit Loads.
Values from Multiframe will not be considered for marking.
Figure 2
Q 2 : Determine the Force in member 2 - 4 of the

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Determine the Force in member 2 - 4 of the steel truss shown in Figure 2 , using Force Method. The stiffness EA is the same for all the members. Note: Determine all required internal actions in the...

Q:

Consider the steel truss shown in ( Figure 1 ) to answer Parts A , B , and C below, where P 1 Consider the steel truss shown in ( Figure 1 ) to answer Parts A , B , and C below, where P 1 = 2 8 k N...

Q:

Consider the steel truss shown in ( Figure 1 ) to answer Parts A , B , and C below, where P 1 = 3 8 k N and P 2 = 5 0 k N . The cross - sectional area of each member is A = 2 5 0 m m 2 , and E = 3 0...

Q:

Method of Virtual Work: Trusses be determined using the equation 1 * = ? ? n 2 v A E , where 1 is the external virtual unit load acting on the truss joint in the direction of , n is the internal...

Q:

Consider the steel truss shown in ( Figure 1 ) to answer Parts A , B , and C below, where P 1 = 3 4 k N and P 2 = 4 6 k N . The cross - sectional area of each member is A = 2 5 0 m m 2 , and E = 1 0...

Q:

k N , and F y = 7 7 . 0 k N , with the directions shown in the figure. Here h = 3 . 0 m and d = 3 . 0 m . Time left 3 : 3 2 Figure P 3 . Truss loaded with various point forces. a ) Determine the...

Q:

nal virtual unit load acting on the truss joint in the if , n is the internal virtual normal force in a truss aused by the external virtual unit load, is the external acement in the desired direction...

Q:

goal ciple of virtual wark, also referred to as the unit - load method, provides a method for detormining the slope cement at a specific point in a structure. For a truss, the method of virtual work...

Q:

4. (Energy Methods) The truss shown in Fig. 4, is made of equilateral triangles with side length L and axial stiffness EA. Movable nodes are numbered starting with j = 1 and the bars starting with i=...

Q:

QUESTION #4 - Trusses 10 kN -2 m- 5 kN 4 m G 45 H 2 m E E K B [20 marks] Figure 3 (Courtesy of Prentice Hall, Adapted) As shown in Figure 3, a truss is designed to support a staircase to move between...

Q:

(a) Exiting from a small linear accelerator near Washington D. C., a proton is moving parallel to the ground. What should the direction(s) of its velocity be in order to maximize the upward component...

Q:

Alas! you have a flat tyre. Using a jack, you lift the punctured tyre off the ground and attempt to switch the tyre for a spare. You will need to undo the lug-nut that is fastening the wheel onto the...

Q:

Problem 8 The following information was taken from the 2 0 2 4 tax files of Jacob, who will use filing status Single in preparation of his 2 0 2 4 federal form 1 0 4 0 . Virginia income tax withheld...

Q:

Exercise 1-6 (Algo) Traditional and Contribution Format Income Statements [LO1-6] Cherokee Incorporated is a merchandiser that provided the following information: Number of units sold Variable...